Description
Key Technical Specifications
| Parameter | Value |
| Manufacturer | Alstom / Grid / GE Renewable Energy |
| Model Number | MVAX31S1DE0754A |
| Relay Type | High-Speed Auxiliary / Tripping Relay |
| Rated DC Voltage | 30 V DC |
| Contact Arrangement | Multiple NO/NC heavy-duty trip contacts |
| Operating Time | \le 10 ms at rated voltage |
| Burden | Low burden auxiliary design |
| Insulation Voltage | 2 kV RMS, 50 Hz for 1 minute between all terminals and earth |
| Operating Temperature | -10 to +55 °C |
| Mounting Type | Drawout / Flush Panel Mounting Case |
Product Introduction & Supply Chain Strategy
The Alstom MVAX31S1DE0754A is an engineered auxiliary tripping relay designed for critical electrical power transmission and distribution protection schemes. It ensures rapid, secure tripping commands to high-voltage circuit breakers upon receiving fault signals from primary protective relays, preventing catastrophic equipment damage across electrical substations.
Procuring this protection-critical component as a New Surplus asset optimizes your TCO and eliminates the inherent reliability hazards of secondary-market refurbished relays. Tripping relays must operate instantaneously and flawlessly during a fault condition; used or repaired units often harbor fatigued coil windings or pitted contacts that can fail to trip under low control-voltage conditions. Deploying an authenticated, factory-sealed surplus unit ensures absolute dependability when safeguarding high-value power assets.

MVAX31S1DE0754A

MVAX31S1DE0754A

MVAX31S1DE0754A

MVAX31S1DE0754A
Installation & Configuration Guide
Stage 1: Pre-Installation (Prep & Safety)
- Enforce strict lock-out/tag-out (LOTO) protocols on the DC tripping supply bus and associated circuit breaker trip coils.
- Put on an ESD-safe grounded wrist strap and ensure proper substation earth-grounding protocols are maintained.
- Verify that the auxiliary relay part number, voltage rating (30 V DC), and contact pinout match the engineering schematics of the protection panel.
Stage 2: Removal
- Isolate the DC supply and trip circuit links to prevent accidental breaker actuation.
- Unlock the drawout relay mechanism or carefully disconnect the rear terminal wiring harness, labeling each lead precisely.
- Extract the relay module straight out from its housing case, avoiding mechanical stress on internal blade connectors.
Stage 3: Installation (Clone & Seat)
- Inspect the panel case, blade contacts, and receptacle spring clips for oxidation, dust, or mechanical distortion.
- Insert the MVAX31S1DE0754A relay securely into its casing or panel mount, engaging locking latches fully.
- Reconnect terminal wiring harnesses or verify that drawout connection pins make solid, low-resistance contact.
Stage 4: Power-On & Testing
- Restore control power to the DC auxiliary bus while keeping breaker trip links isolated for preliminary testing.
- Perform an electrical trip simulation test to verify correct coil pick-up voltage, mechanical target flag operation, and contact closure timing.
- Re-engage the main breaker trip links and sign off on the protection scheme return-to-service.
Firmware/Software Versions & Upgrade Notes
- Configuration Baseline: The MVAX31S1DE0754A is an electromechanical or static auxiliary hardware relay operating without software firmware requirements. Configuration relies entirely on internal jumper settings and physical contact blocks.
- Compatibility Notes: Direct drop-in replacement for legacy Alstom/Areva MVAX variants sharing identical voltage codes and case dimensions. Do not interchange coils with different DC voltage ratings (e.g., substituting 30 V DC with 110 V DC).
- Replacement Strategy: Always verify coil voltage ratings and contact multiplier configurations against substation drawings before installation to prevent coil burnout or mistripping.
Frequently Asked Questions (FAQ)
Are these units genuinely new, or are they refurbished?
This unit is a Brand New Surplus protection relay. It is entirely unused, preserved in original factory packaging, and has never been installed in an active substation panel or subjected to third-party bench repairs.
Why is New Surplus essential for substation tripping relays?
Tripping relays are the final link in clearing electrical faults. Refurbished or repaired relays may have weakened coil insulation or degraded contact springs that fail to actuate during a high-stress system fault. New Surplus guarantees 100 percent original OEM operational integrity.
What is the significance of the 30 V DC rating?
The 30 V DC rating specifies the nominal control voltage required to energize the relay coil reliably. Operating this unit on an incorrect DC voltage level can cause failure to pick up or result in thermal overload.
Do MVAX relays require periodic maintenance?
While highly reliable, routine substation maintenance windows should include visual checks of mechanical target flags, contact cleanliness, and functional trip tests.
What warranty is provided with this unit?
This New Surplus unit is backed by a full 1-year operational warranty, ensuring absolute compliance and safety assurance across your power distribution infrastructure.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626