Description
Core Product Summary
The Basler SCA-SS-70-10 is a four-quadrant PWM servo amplifier designed for brush-commutated DC motors with an output capability up to 700 W. It is a compact, panel-mountable drive module for single-motor motion-control applications requiring reversible torque and speed control.
The amplifier operates from an 11–70 VDC supply and provides 10 A nominal current with a 20 A impulse-current rating. Its front-mounted jumpers select one of six operating modes: torque control, IxR control, DC-tacho control, digital-encoder speed control, voltage control, and analog positioning. Screw terminals support power, motor, control, and feedback connections.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer | Basler Electric / E-Motion |
| Model | SCA-SS-70-10 |
| Product type | Four-quadrant PWM servo amplifier |
| Motor type | Brush-commutated DC motor |
| Maximum motor power | 700 W with heatsink mounting |
| Power-supply voltage | 11–70 VDC |
| Nominal current | 10 A |
| Impulse / peak current | 20 A |
| Power-output-stage frequency | 49 kHz ± 10% |
| Efficiency | 95% |
| Current-controller bandwidth | 2.5 kHz |
| Internal choke | 370 µH |
| Analog setpoint | -10 to +10 VDC |
| Encoder input | Channels A and B, TTL, maximum 100 kHz |
| Tacho input | Maximum 50 VDC, 100 kΩ input resistance |
| Enable / disable inputs | 8–30 VDC |
| Auxiliary outputs | +5 VDC / 100 mA for Hall sensors; +15 VDC / 20 mA auxiliary supply |
| Status indication | Two-color green/red LED for OK / fault |
| Dimensions | 180 × 100 × 40 mm (L × W × H) |
| Mounting-hole spacing | 120 × 90 mm |
| Weight | 650 g with terminal connector; 740 g listed in catalog data |
| Operating temperature | -10 to +45°C |
| Protection functions | Overcurrent, overtemperature, output short circuit, and undervoltage protection |
Engineering Selection Highlights
- The SCA-SS-70-10 is intended for brushed DC motors, so it is not a direct selection for brushless servo motors without verifying the complete drive architecture.
- Its 11–70 VDC supply range allows use with different DC power supplies, but the supply must never exceed 70 VDC or be connected in reverse.
- The 10 A continuous and 20 A peak ratings should be compared with the motor’s continuous and acceleration-current requirements.
- The 700 W maximum power rating applies with heatsink mounting, making thermal mounting an important selection and installation condition.
- Six selectable control modes allow matching to torque control, speed feedback from a tacho or encoder, voltage control, or analog positioning.
- TTL encoder inputs on channels A and B support digital speed control up to 100 kHz.
- The 180 × 100 × 40 mm housing and 120 × 90 mm mounting-hole spacing should be checked against the available panel or heatsink layout.

SCA-SS-70-10

SCA-SS-70-10
System Compatibility & Integration Requirements
| Item / Dependency | Verified Compatibility or Requirement | Practical Note |
|---|---|---|
| Motor type | Brush-commutated DC motor | Confirm the connected motor is brushed DC before using this amplifier. |
| Motor capacity | Up to 700 W with heatsink mounting | Match motor power and thermal mounting to the amplifier rating. |
| Power supply | Single DC supply, 11–70 VDC | Supply polarity and voltage limit are critical; exceeding 70 VDC or reversing polarity can destroy the unit. |
| Control mode | Selected by front-side jumpers | Set the required mode before commissioning. |
| Speed feedback | DC tacho or TTL encoder, channels A and B | Use the feedback device appropriate to the selected operating mode. |
| Analog command | -10 to +10 VDC setpoint | Suitable for analog motion-control or PLC analog-output interfaces. |
| Digital inputs | Enable, disable reverse, and disable forward; 8–30 VDC | Interface these inputs with a controller output rated for the required voltage range. |
| Connections | Screw terminals for supply, motor, control, and feedback | Plan cabinet wiring and terminal access around screw-terminal connections. |
Dimensions, Mounting & Connection Notes
- Dimensions: 180 mm length × 100 mm width × 40 mm height.
- Mounting-hole spacing: 120 × 90 mm.
- Weight: 650 g including the terminal connector; catalog data also lists 740 g.
- The aluminum housing supports different mounting methods and is designed for panel or heatsink integration.
- Screw terminals are used for control and feedback inputs, supply power, and motor connections.
- The operating-temperature range is -10 to +45°C.
- The 700 W output rating is specified with heatsink mounting, so heatsink selection and mounting are material to thermal performance.
Detailed Product Overview
The Basler SCA-SS-70-10 is a compact four-quadrant PWM servo amplifier for brush-commutated DC motors. Its four-quadrant output stage permits controlled operation and braking in both directions, which is relevant for positioning axes, reversible conveyors, feed axes, and other single-motor motion applications.
The model designation defines its principal electrical envelope: a 70 VDC maximum supply voltage and a 10 A nominal current rating. The amplifier also supports a 20 A impulse current, allowing short-duration acceleration or load-transient demands within the drive’s protection limits. The maximum continuous output capability is specified as 700 W when the unit is mounted on a heatsink, so thermal design should be treated as part of drive selection rather than an afterthought.
Configuration is performed locally through front-mounted jumpers. The available modes are torque control, IxR control, DC-tacho control, speed control using digital-encoder feedback, voltage control, and analog positioning. This range allows the same hardware platform to be adapted to different feedback and command architectures, provided the connected motor and feedback devices match the selected mode.
For encoder-based speed control, the amplifier accepts TTL signals on channels A and B up to 100 kHz. For tacho-based control, it accepts a DC tachometer signal up to 50 VDC through a 100 kΩ input. The analog setpoint input accepts -10 to +10 VDC, providing a conventional interface for PLC analog outputs, motion controllers, or manual command sources.
The drive includes protection against overcurrent, overtemperature, output short circuit, and undervoltage. A two-color LED provides OK and fault indication. Auxiliary outputs include +5 VDC at 100 mA for Hall sensors and +15 VDC at 20 mA for auxiliary circuit requirements. These supplies should be treated as auxiliary power sources with defined current limits, not as general-purpose cabinet power supplies.
Installation uses screw terminals for supply, motor, control, and feedback wiring. The 180 × 100 × 40 mm housing, 120 × 90 mm mounting-hole spacing, and -10 to +45°C operating range should be checked against the enclosure layout, ambient conditions, and heatsink arrangement before integration.
Applications & System Role
The SCA-SS-70-10 sits between a DC power supply and a single brushed DC motor in a motion-control axis. It converts an analog command or feedback-based control signal into a four-quadrant PWM output, enabling motor operation in both directions with controlled torque and speed.
Its operating modes make it suitable for systems using a DC tachometer, incremental encoder, analog command signal, or analog positioning interface. The amplifier can function as an independent speed controller or as part of a higher-performance servo axis where encoder feedback and closed-loop control are required.
FAQ
What is the Basler SCA-SS-70-10?
It is a four-quadrant PWM servo amplifier for brush-commutated DC motors, rated for 10 A continuous current and up to 700 W output with heatsink mounting.
What supply voltage does the SCA-SS-70-10 require?
It requires a single DC power supply within the 11–70 VDC range.
What are its current ratings?
The amplifier is rated for 10 A nominal current and 20 A impulse current.
Which motors can it drive?
It is designed for brush-commutated DC motors, with a maximum output capability of 700 W when heatsink-mounted.
Which control modes does it support?
It supports torque control, IxR control, DC-tacho control, digital-encoder speed control, voltage control, and analog positioning.
How is the operating mode selected?
The required operating mode is selected by setting jumpers on the front side of the module.
What feedback inputs are available?
It accepts TTL encoder signals on channels A and B up to 100 kHz and a DC-tacho signal up to 50 VDC.
What are its dimensions and mounting-hole spacing?
The housing measures 180 × 100 × 40 mm, with a 120 × 90 mm mounting-hole spacing.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626