Description
Key Technical Specifications
Bosch Rexroth identifies R911274054 as the MHD041B-144-PG1-UN servomotor. Confirm the drive match, cooling requirements, feedback interface, and brake wiring against the motor nameplate and applicable Rexroth documentation before installation.
- Manufacturer: Bosch Rexroth Indramat.
- Model: MHD041B-144-PG1-UN.
- Rexroth part number: R911274054.
- Motor type: Permanent-magnet synchronous servomotor.
- Frame / length: 041 / B.
- Winding code: 144.
- Flange / centering diameter: 82 mm / 50 mm.
- Continuous torque at standstill: 2.7 Nm.
- Holding brake torque: 2.2 Nm.
- Feedback: Digital servo feedback with absolute position detection over more than 4,096 revolutions.
- Cooling: Liquid-cooled per a product listing; verify required coolant and operating conditions in the applicable Rexroth documentation.
- Shaft / seal: Plain shaft with shaft seal.
- Protection rating: IP65, as listed by a Rexroth-series reseller.
- Connector orientation: Power and feedback connectors can rotate within a 270° range.
Product Introduction
Bosch Rexroth Indramat MHD041B-144-PG1-UN (R911274054) is a permanent-magnet synchronous servomotor for industrial motion axes. This 041-frame, B-length motor has an 82 mm flange, 50 mm centering diameter, plain shaft with seal, and digital absolute feedback.
The configuration includes a 2.2 Nm holding brake and is listed as liquid-cooled. Verify drive compatibility, feedback evaluation, brake release wiring, and coolant requirements before fitting it to an existing machine. The part number alone does not confirm that a used or surplus motor has passed functional testing.

MHD041B-144-PG1-UN

MHD041B-144-PG1-UN
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to This Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Motor does not turn | Drive enable, power wiring, interlock, or drive fault | Possible | Check the drive fault history and verify motor power connections against the wiring diagram with power isolated | Verify the drive, supply, and interlocks before replacing the motor |
| Drive reports feedback or encoder fault | Feedback cable, connector, drive setup, or encoder fault | High | Inspect the feedback connector and cable; compare the configured feedback type with the motor documentation | Confirm the motor and drive feedback compatibility before swapping parts |
| Axis moves but position is incorrect | Feedback configuration, cabling, or mechanical coupling issue | Possible | Check drive feedback diagnostics and inspect the coupling and encoder cable | Verify drive configuration and mechanical alignment before condemning the motor |
| Brake does not release | Brake supply, wiring, output circuit, or brake fault | High | Check the brake circuit voltage at the documented terminals during the commanded release; use the motor/drive wiring diagram | Confirm brake supply and wiring; do not apply an assumed voltage |
| Motor overheats or trips | Cooling flow, overload, drive setup, or mechanical load issue | High for liquid-cooled configuration | Verify coolant flow and temperature against the machine documentation; check drive load and motor temperature diagnostics | Correct cooling or overload issues before replacing the motor |
| Shaft or bearing noise | Coupling misalignment, bearing wear, contamination, or mechanical damage | Possible | Isolate the axis and inspect shaft play, coupling alignment, and seal condition according to site procedure | Have the motor evaluated before returning it to service |
Frequently Asked Questions (FAQ)
What is the Bosch Rexroth MHD041B-144-PG1-UN?
It is an MHD-series permanent-magnet synchronous servomotor. The OEM product page associates the model with Rexroth part number R911274054.
What does the “PG1” configuration mean?
The motor is listed with digital feedback and absolute position detection. Confirm the exact encoder interface and drive compatibility in the motor documentation; do not select a replacement based only on a similar model suffix.
Is this motor a direct replacement for another MHD041B motor?
Not automatically. Match the complete model code, winding, feedback, brake, shaft, cooling arrangement, and connector configuration. Confirm the drive supports the replacement’s feedback and motor data.
Does the motor need liquid cooling?
A product listing describes this exact configuration as liquid-cooled. Check the motor label and applicable Rexroth documentation for coolant type, required flow, and operating limits before commissioning.
Can I replace it without losing position reference?
Do not assume so. Although the motor is listed with absolute position feedback, drive behavior after a motor or encoder change depends on the control system and commissioning procedure. Back up parameters and follow the machine builder’s reference and startup procedure.
Is the unit new surplus or refurbished, and what warranty applies?
That depends on the seller and the specific unit. Request written confirmation of condition, serial number, test scope, warranty duration, and return terms. A reseller’s stock or warranty statement is not proof of factory-new condition or OEM warranty coverage.
What should I verify before ordering?
Send the seller a clear photo of the nameplate and connector end. Confirm the full model code, R911274054, winding, feedback type, brake configuration, cooling requirements, and the condition and test documentation for the exact unit.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626