Description
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Manufacturer | Bosch Rexroth Indramat |
| Model | MHD071B-035-PP1-UN |
| Manufacturer part number | R911283445 |
| Motor technology | Synchronous permanent-magnet servo motor |
| Motor frame | 071B |
| Winding code | 035 |
| Rated speed | 2,500 rpm |
| Continuous standstill torque | 8.0 Nm, natural cooling; 12.0 Nm, surface cooling in the published MHD071B-035 table |
| Continuous standstill current | 6.3 A for the natural-cooling, 60 K overtemperature specification |
| Peak current | 28.3 A in the published MHD071B-035 data |
| Torque constant | 1.38 Nm/A at 20°C, using the catalog’s specified current convention |
| Rotor moment of inertia | 8.7 × 10⁻⁴ kg·m², without holding brake |
| Feedback | Digital servo feedback with integrated multiturn absolute encoder |
| Position detection | Absolute multiturn feedback; confirm exact encoder version |
| Shaft | Keyed shaft with sealing ring |
| Flange size | 115 mm |
| Centering diameter | 95 mm |
| Holding brake | Installed; torque rating requires confirmation |
| Protection rating | IP65 when correctly installed with specified power and feedback cables |
| Insulation class | F |
| Permitted ambient temperature | 0°C to +40°C in the cited project-planning data |
| Storage and transport temperature | −20°C to +80°C |
Specification qualification: The published MHD071B-035 table gives different continuous torque values for natural and surface cooling. These figures describe cooling-dependent motor configurations and should not be combined into a single guaranteed rating for every suffix variant. Confirm the complete ordering code and motor nameplate before sizing the drive or calculating the machine’s load capacity.
Product Introduction & Supply Chain Strategy
The Bosch Rexroth Indramat MHD071B-035-PP1-UN is intended for servo-driven machinery requiring controlled acceleration, repeatable positioning, and feedback to a compatible drive controller. Its keyed shaft supports positive mechanical coupling, while absolute multiturn feedback can simplify position recovery when the complete drive and feedback system is configured to support it. Actual performance depends on the drive, cooling arrangement, load profile, and motion cycle.
For procurement, exact suffix matching is important. A motor with a similar MHD071 frame designation may have a different winding, encoder, cooling arrangement, or brake configuration. Compare the full ordering code and manufacturer part number, then verify shaft dimensions, connector orientation, brake rating, and drive compatibility. For critical axes, retain a record of the installed drive parameters and the original motor nameplate to reduce replacement delays.

MHD071B-035-PP1-UN

MHD071B-035-PP1-UN
Installation & Configuration Guide
Stage 1 — Pre-installation inspection
- Verify the complete motor designation and part number R911283445.
- Compare the nameplate with the original motor’s rated data.
- Confirm cooling requirements, holding-brake rating, feedback type, and drive compatibility.
- Check flange dimensions, centering diameter, shaft key, and shaft seal.
- Inspect the motor housing, connectors, and shaft for shipping damage.
Stage 2 — Remove the existing motor
- Stop the machine and follow site lockout/tagout procedures.
- Isolate the drive supply and wait for the manufacturer’s specified DC-bus discharge period.
- Secure the driven load before disconnecting the motor, particularly on vertical axes.
- Label the motor-power, feedback, and brake connections.
- Support the motor before removing mounting fasteners and coupling hardware.
Stage 3 — Install and connect
- Mount the motor using the specified fasteners and tightening torques.
- Align the shaft and coupling within the machine manufacturer’s tolerances.
- Connect motor power and feedback using cables approved for the drive and motor.
- Verify protective grounding, connector seating, and cable routing.
- Confirm the brake circuit and the required cooling method before enabling the drive.
Stage 4 — Commission and test
- Confirm that the drive recognizes the motor and feedback device correctly.
- Check the motor parameters, current limits, speed limits, and feedback direction.
- Verify brake operation using the drive manufacturer’s approved test procedure.
- Run a controlled, low-speed test and check for abnormal vibration, noise, or temperature.
- Validate position accuracy and safety functions before returning the axis to production.
Installation caution: Do not assume that the brake is a safety-rated holding device for every application, or that the motor can be hot-swapped. Use the machine’s approved load-support and electrical isolation procedures.
Firmware, Software & Configuration Notes
The MHD071B-035-PP1-UN is a servo motor, not a standalone programmable controller. Its configuration is managed through a compatible Bosch Rexroth drive and the associated engineering tools.
- Motor identification: Select or verify the exact motor type in the drive configuration.
- Feedback setup: Confirm the integrated encoder type and supported feedback interface.
- Drive parameters: Back up the original motor and drive parameters before replacement.
- Brake control: Verify brake release timing, holding behavior, and drive output configuration.
- Thermal configuration: Use the correct motor cooling data when setting continuous current and torque limits.
- Firmware: The available sources do not establish one specific firmware version for this motor. Check the installed drive’s firmware and supported motor database.
- Encoder retention: Absolute position retention depends on the encoder and drive configuration; verify the machine’s homing and position-recovery procedure after replacement.
Do not use a parameter set from a different MHD071 variant without verifying the winding, encoder, brake, and cooling configuration.
Frequently Asked Questions
Q1. What is the -PP1-UN used for?
It is a synchronous servo motor for industrial motion-control applications that require controlled rotary motion and feedback to a compatible servo drive.
Q2. What is its manufacturer part number?
The associated part number is R911283445. Match this number and the full MHD ordering code against the physical nameplate before purchasing.
Q3. What is the motor’s continuous torque?
The Bosch Rexroth technical table lists 8.0 Nm for natural cooling and 12.0 Nm for surface cooling under the specified thermal conditions. The correct rating for a particular motor depends on its exact configuration.
Q4. Does it have a holding brake?
Yes, supplier listings identify this variant as equipped with a holding brake. However, published listings disagree on the brake’s torque rating. Verify the nameplate and exact Bosch Rexroth documentation before using it in load-holding calculations.
Q5. Can it directly replace another MHD071 motor?
Not necessarily. Verify winding code, encoder type, cooling configuration, shaft dimensions, brake, and drive compatibility. Matching only the frame size is insufficient to establish interchangeability.
Q6. Is the motor still in production?
The sources reviewed do not conclusively establish current production status. Confirm manufacturer support, stock availability, and repair options before deciding on a long-term spare-parts strategy.
Q7. How should New Original or New Surplus condition be verified?
Request photographs of the actual motor and nameplate, the complete ordering code, serial or date-code information where available, and written confirmation of condition and warranty. Do not infer unused condition from external appearance alone.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626