Sale!

Bosch Rexroth MSK070C-0150-NN-M1-UP1-NNNN IndraDyn S Servo Motor

  • Model: MSK070C-0150-NN-M1-UP1-NNNN
  • Brand: Bosch Rexroth (Indramat)
  • Series: IndraDyn S / MSK
  • Core Function: Permanent-magnet synchronous servo motor with holding brake
  • Product Type: AC Servo Motor
  • Key Specs: Size 070, length C, natural convection, multiturn absolute optical encoder (Hiperface, 128 periods), keyway shaft, 23 Nm electrically released holding brake
  • Condition: New Original / New Surplus
Categories: , , , , SKU: MSK070C-0150-NN-M1-UP1-NNNN Brand:

Description

3. Key Technical Specifications

  • Motor size / length: 070 / C
  • Winding code: 0150
  • Cooling: Natural convection (NN)
  • Encoder: Optical multiturn absolute, Hiperface interface, 128 signal periods (M1)
  • Shaft: With keyway (DIN 6885) and shaft sealing ring
  • Holding brake: Electrically released, 23 Nm (UP1)
  • Maximum speed: 2500 rpm
  • Maximum torque: 33 Nm
  • Standstill torque: approx. 13–14.5 Nm (depending on thermal condition)
  • Standstill current: approx. 8.1 A
  • Peak current: 16.4 A
  • Protection rating: IP65
  • Connectors: Rotatable (typically 240°)
  • Design: Standard (NNNN)
  • Typical material number: R911310291
  • Operating temperature: 0 °C to 40 °C (standard)
  • Note: Exact continuous torque and current values depend on ambient temperature, mounting, and drive settings. Always verify against the motor nameplate and Rexroth project planning data.

4. Product Introduction

The Bosch Rexroth MSK070C-0150-NN-M1-UP1-NNNN is a robust IndraDyn S synchronous servo motor designed for applications requiring higher continuous torque at moderate speeds. It features natural convection cooling, a multiturn absolute optical encoder with Hiperface interface, a keyed shaft, and a 23 Nm electrically released holding brake.

This motor is commonly used in machine tools, packaging equipment, material handling, and general automation systems where reliable position holding and absolute feedback are required. It integrates directly with Rexroth IndraDrive controllers for precise motion control.

MSK070C-0150-NN-M1-UP1-NNNN

MSK070C-0150-NN-M1-UP1-NNNN

MSK070C-0150-NN-M1-UP1-NNNN

MSK070C-0150-NN-M1-UP1-NNNN

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Motor does not hold position when stopped Brake not engaging or brake circuit fault ✅ High Check 24 V brake supply and diagnostic status Verify brake wiring and parameters; replace motor if brake fails
Overtemperature fault Overloaded or restricted cooling ✅ High Monitor motor temperature and ambient conditions Ensure free air circulation; reduce duty cycle if needed
Position error or loss of absolute data Encoder or cable issue ✅ High Check Hiperface communication and multiturn status Inspect encoder cable/connector; replace motor if encoder is faulty
Drive reports brake error Brake feedback or parameterization problem ✅ High Review brake diagnostics in the drive Confirm correct brake settings and wiring
Excessive noise or vibration Mechanical misalignment or bearing wear ✅ Medium Check coupling, mounting, and shaft run-out Verify mechanical installation; replace motor if bearings are damaged
Motor not identified by drive Incorrect parameter set ✅ High Compare nameplate type code with drive motor data Load the correct MSK070C-0150 parameters

If the issue cannot be isolated, photograph the nameplate (full type code and material number) and contact technical support with drive diagnostics.

6. Frequently Asked Questions (FAQ)

Q: What type of motor is the MSK070C-0150-NN-M1-UP1-NNNN?
A: It is a Bosch Rexroth IndraDyn S permanent-magnet synchronous servo motor, size 070, length C, with an integrated holding brake.

Q: Does this motor have a holding brake?
A: Yes. It includes a 23 Nm electrically released holding brake (UP1 option).

Q: What encoder is installed?
A: Optical multiturn absolute encoder with Hiperface interface and 128 signal periods (M1).

Q: How is the motor cooled?
A: Natural convection (NN). Adequate free air circulation around the motor is required.

Q: What is the maximum speed and torque?
A: Maximum speed is 2500 rpm; maximum torque is 33 Nm.

Q: Is the shaft keyed?
A: Yes. This version has a keyway shaft (DIN 6885) with shaft sealing ring.

Q: What condition and warranty do you offer?
A: We supply New Original / New Surplus stock. Units are inspected for basic functionality. Standard coverage is a 1-year warranty against defects. Always provide the complete type code MSK070C-0150-NN-M1-UP1-NNNN (and material number if available) when ordering or requesting support.