Description
Key Technical Specifications
| Parameter | Specification / Value |
| Manufacturer | Emerson Automation Solutions |
| Part Number | KJ3241X1-EA1 |
| Assembly Code | VE4050S2B1 |
| System Platform | Emerson DeltaV DCS |
| Interface Types | RS232, RS422, RS485 (Half/Full Duplex) |
| Redundancy Support | Dual redundant serial card carrier connection |
| Baud Rates Supported | 300 bps to 115.2 kbps |
| Isolation Rating | 1000 VAC galvanic isolation field-to-bus |
| Field Termination | Screw terminal connections / Shield grounding clamps |
| Power Consumption | Drawn via backplane carrier (5 VDC, 150 mA max) |
| Operating Temperature | −40°C to +70°C (−40°F to +158°F) |
| Humidity Range | 5% to 95% relative humidity (non-condensing) |
Product Introduction & Supply Chain Strategy
The Emerson KJ3241X1-EA1 (VE4050S2B1) is a redundant serial interface terminal block engineered to route RS232, RS422, and RS485 communication lines directly into Emerson DeltaV DCS serial cards. It delivers physical signal termination, shielding, and isolation for critical field-to-DCS data exchanges, including Modbus RTU connections to variable frequency drives, power meters, chromatographs, and third-party PLCs. Engineered for high availability, this terminal assembly allows redundant serial cards to operate seamlessly, preventing single-point communication failures in complex process control architectures.
Sourcing this module as New Surplus secures full OEM-grade signal integrity without paying factory list prices or dealing with extended manufacturer lead times. Unlike used equipment, genuine New Surplus parts guarantee intact terminal block contacts, clean backplane connectors, and zero thermal degradation. Carrying a dedicated buffer stock of 1–2 unused terminal blocks on-site protects your plant against costly downtime caused by field wiring shorts, electrical surges, or lightning strikes on serial loops.

KJ3241X1-EA1

KJ3241X1-EA1
Installation & Configuration Guide
1.Pre-Installation (Prep & Safety):Prerequisite.
Perform Lock-Out/Tag-Out (LOTO) on connected serial field lines and external power sources. Wear a grounded ESD wrist strap attached to the cabinet ground. Document existing DIP switch or jumper settings and tag each serial conductor (TX, RX, Shield, Ground) carefully before disconnect.
2.Removal:Mechanical extraction.
Unscrew field wiring terminals or disconnect serial pin blocks. Disengage the top and bottom carrier locking latches on the terminal assembly. Pull the KJ3241X1-EA1 straight out off the DeltaV carrier rail guides to prevent bending or warping backplane connector pins.
3.Installation (Clone & Seat):Hardware mounting.
Inspect gold connector pins on the replacement KJ3241X1-EA1 for bent pins or dust. Align terminal block guide slots with carrier rail guides. Firmly push the block onto the backplane until both side latches engage with a distinct click. Re-connect serial wiring conductors strictly matching the original channel pinout.
4.Power-On & Testing:Verification.
Restore 24 VDC bus power to the carrier assembly. Check that the DeltaV serial I/O card LEDs show active communication (TX/RX blinking green). Open DeltaV Diagnostics and confirm that the serial card status reports normal operation without channel noise or protocol framing errors.
Firmware/Software Versions & Upgrade Notes
- System Compatibility: Compatible with DeltaV v11.3.1 through v15.3 systems utilizing standard or redundant serial interface cards.
- Firmware Pass-Through: The KJ3241X1-EA1 is a passive/active physical termination assembly and does not host flash firmware directly. Revisions (e.g., Rev A through Rev H) maintain backward and forward hardware compatibility across DeltaV 2-wide and 8-wide carrier bases.
- Protocol & Driver Configuration: Ensure the baud rate, parity, stop bits, and protocol driver (e.g., Modbus RTU Master/Slave) set in DeltaV Explorer match the external serial device settings exactly.
- Redundancy Precaution: When replacing terminal blocks on a redundant pair, verify that both active and standby serial cards recognize identical port configurations to prevent failover sync drops.
Frequently Asked Questions (FAQ)
Q: Is this Emerson KJ3241X1-EA1 unit brand new or refurbished?
A: This product is a Brand New Surplus unit. It is not used, not pulled from a decommissioned plant, and not refurbished. All modules undergo rigorous quality verification to ensure OEM-level reliability.
Q: Why should we buy New Surplus instead of cheaper refurbished serial cards?
A: Refurbished communication components often carry invisible internal wear, such as degraded isolation optocouplers and weakened terminal screws from over-tightening. A failed 400 refurbished serial block can halt communication to an entire tank farm or boiler control PLC, causing downtime costs in excess of 50,000 in lost production.
Q: Does this terminal block support both RS232 and RS485 protocols?
A: Yes, the terminal block supports RS232, RS422, and 2-wire/4-wire RS485 communication standards. Pin selection and configuration depend on field wiring termination and software driver settings in DeltaV.
Q: Can I hot-swap the on an active DeltaV system?
A: Yes, DeltaV carriers allow hot-swapping terminal blocks. However, you should temporarily disable active serial polling or disconnect external field communications power to prevent transient voltage spikes across backplane contacts during removal.
Q: Does this terminal block hold port settings or Modbus address logic?
A: No, the is an interface termination assembly. All Modbus register mapping, baud rate selections, device addresses, and serial driver logic are stored in the DeltaV Controller and Serial I/O Module memory. Swapping the hardware requires zero software reprogramming.
Q: What warranty coverage is included with this New Surplus assembly?
A: We supply this unit with a full 1-year operational replacement warranty. Every block is verified for backplane continuity and packaged in ESD-safe shielding before shipment to ensure immediate operational readiness upon arrival.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626