WhatsApp: +86 16626708626
Email: 
Phone: +86 16626708626Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Model | IS2020DRLYH1AA |
| Manufacturer | General Electric (GE) |
| Series | Speedtronic Mark VI |
| Module type | Simplex Relay Output Module |
| Mounting | Wall-mounted chassis (not rack-mounted) |
| Application | Simplex (non-redundant) control applications only |
| Output type | Relay output terminals |
| Function | Interface relay output for control signals to field devices |
| Integration | Part of Mark VI turbine control system |
| Redundancy | Simplex only (no redundancy support) |
| Typical use | Valve control, alarm outputs, interlock signals in turbine systems |
| Country of origin | USA |
Product Introduction
GE IS2020DRLYH1AA is a Simplex Relay Output Module for the Speedtronic Mark VI turbine control system. It is designed as a wall-mounted relay output terminal board for simplex (non-redundant) applications only.
This module is selected when the existing relay output terminal fails or when expanding control outputs in a simplex Mark VI configuration. Buyers prioritize exact model match and confirm simplex-only application because this unit cannot be used in redundant or dual-redundant setups.
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to This Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Relay output does not activate despite control signal | Faulty relay coil, blown fuse, or power supply issue | ✅ High | Measure voltage at relay coil terminals; check fuse and power supply | Replace fuse if blown, check power supply, then replace module if relay fails |
| Intermittent relay switching or chatter | Loose terminal wiring, worn relay contacts, or noisy signal | ✅ High | Inspect terminal block connections; measure control signal stability | Tighten terminals, add noise filtering if signal is unstable |
| No response from field device (valve, alarm) | Open circuit in relay output, broken field wiring, or device fault | ✅ High | Check continuity through relay contacts; test field device separately | Replace relay module if contacts are open; repair field wiring if needed |
| Multiple relay outputs fail simultaneously | Power supply failure or backplane fault (if applicable) | ❌ Low | Measure supply voltage to the module; check other modules on same power | Fix power supply first before replacing module |
If you are stuck, send photos of terminal wiring, relay status LEDs (if any), fuse condition, and diagnostic logs to technical support.
- IS2020DRLYH1AA
Frequently Asked Questions
Q: What is GE IS2020DRLYH1AA?
A: It is a GE Speedtronic Mark VI Simplex Relay Output Module designed for wall mounting. It provides relay output terminals for control signals to field devices like valves and alarms.
Q: Is this a direct replacement?
A: Only if your existing system uses IS2020DRLYH1AA in a simplex Mark VI configuration. This module is wall-mounted and simplex-only, so verify mounting style and redundancy requirements before installation
Q: Is it new, used, or refurbished?
A: This listing is positioned as New Surplus—unused inventory from prior stock. Condition should be clearly stated, and testing status should be confirmed with the seller.
Q: Can I use this in a redundant (dual) Mark VI system?
A: No. The IS2020DRLYH1AA is designed for simplex (non-redundant) applications only. Using it in a redundant system could compromise system reliability and violate design specifications.
Q: What should I check before swapping the module?
A: Photograph the old terminal wiring, note the wall-mount location, verify power is off, confirm fuse condition, and check that the new module matches the exact part number. A bad swap often starts with assuming compatibility.
Q: Why is surplus cheaper than factory stock?
A: Surplus pricing reflects secondary-market sourcing, limited availability, and older inventory. The lower price does not mean it is the same as factory-new sealed stock, so testing and condition must be transparent.
Q: Does this part come with a warranty?
A: Warranty terms depend on the seller. For B2B buyers, confirm testing status, return terms, and whether a test report is included. Typical industrial surplus listings offer 1-year warranty on tested units.
