WhatsApp: +86 16626708626
Email: 
Phone: +86 16626708626Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer | General Electric |
| Model | IS215UCVEM08 |
| Functional Acronym | UCVE |
| Alternate Reference | UCVE08A; verify exact compatibility |
| System Family | GE Mark VI Speedtronic |
| Platform | US2000 controller architecture |
| Module Type | Single-slot VME controller / PC control module |
| Processor | Intel Celeron, 300 MHz; verify board revision |
| Operating System | QNX real-time operating system |
| System Memory | 32 MB DRAM; verify actual board configuration |
| Ethernet | One 10BaseT/100BaseTX RJ-45 port |
| Serial Ports | COM1 and COM2, RS-232C |
| Service Display | SVGA monitor interface |
| Peripheral Interfaces | Keyboard and mouse connections |
| Local Storage | CompactFlash or other installed storage; verify actual unit |
| Controller Memory | Battery-backed SRAM; verify battery condition |
| Status Indication | Three front-panel status LEDs |
| Backplane | VME bus |
| Installation | Mark VI controller rack; verify intended slot |
| Typical Supply | 125 V DC Mark VI rack supply; verify cabinet documentation |
| Operating Temperature | 0 to 60 °C; confirm applicable system specification |
| Software Image | Site-specific GE Mark VI application; verify before purchase |
| Configuration | Site-specific controller and network settings; not automatically included |
Supplier references identify the IS215UCVEM08 as a Mark VI UCVE controller with Ethernet, two RS-232C ports, and service interfaces. Processor, memory, storage, software image, and exact power requirements should be verified against the board revision and GE documentation.
Product Introduction
The GE IS215UCVEM08 is a single-slot VME UCVE controller for GE Mark VI Speedtronic turbine-control systems. It executes turbine-control software and communicates with the Mark VI control architecture through one 10BaseT/100BaseTX Ethernet port and two RS-232C serial ports.
The US2000-based controller also provides SVGA, keyboard, and mouse service connections. Verify the exact processor, memory, storage media, QNX software image, battery condition, rack slot, Ethernet configuration, and approved replacement status before commissioning.
IS215UCVEM08
IS215UCVEM08
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to This Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Controller does not power up | Missing 125 V DC rack supply, blown fuse, poor VME seating, backplane fault | ✅ High | Verify rack power at the approved test points and inspect the board’s VME connectors | Check rack supply and seating before replacing the controller |
| No normal startup sequence | Failed processor, corrupted storage image, memory fault, incorrect board revision | ✅ High | Observe the three status LEDs and connect an approved service monitor if available | Record the startup code and verify the installed software image |
| Mark VI system reports controller offline | Ethernet cable, IONet/network fault, wrong address, failed controller interface | ✅ High | Test the cable and switch port; verify IP configuration and network diagnostics | Correct the network path before condemning the UCVE board |
| Ethernet link LED remains off | No link partner, incorrect cable, failed RJ-45 interface, switch disabled | ⚠️ Medium | Connect to a known-good switch port and check link status at both ends | Replace cable or switch port first; test the board only after the physical link is proven |
| COM1 or COM2 does not communicate | Incorrect pinout, baud rate, handshaking, cable, or failed serial port | ⚠️ Medium | Perform a controlled serial loopback test with the approved cable and port settings | Verify the service device and cable before replacing the controller |
| Controller repeatedly reboots | Unstable rack supply, overheating, failed memory, damaged storage media | ✅ High | Trend supply voltage and temperature; inspect boot logs and storage diagnostics | Correct power and cooling issues before installing another controller |
| QNX fails to boot | Corrupt CompactFlash or software image, storage failure, memory fault | ✅ High | Inspect boot messages and compare the storage media with a verified image | Restore only the approved Mark VI image; do not use a generic QNX image |
| Application loads but turbine control remains unavailable | Wrong configuration, missing network parameters, incompatible software revision | ✅ High | Compare controller configuration, IP settings, application version, and rack assignment with the original | Restore the site-specific configuration and validate with the system owner |
| SVGA monitor shows no service output | Monitor/cable issue, incorrect boot stage, failed video interface | ⚠️ Medium | Test with a known-good compatible monitor and verify controller startup indicators | Treat video loss separately from controller failure |
| Keyboard or mouse is unresponsive | Peripheral compatibility, connector fault, service-port configuration | ❌ Low | Test known-good peripherals during a controlled service session | Use the Mark VI-approved service hardware; process control may still be operational |
| Several Mark VI functions fail simultaneously | Controller failure, VME bus fault, common rack power loss | ✅ High | Check rack power, controller LEDs, VME diagnostics, and communication with adjacent cards | Diagnose common infrastructure before replacing multiple I/O boards |
| Replacement controller will not assume control | Wrong UCVE variant, incompatible software image, configuration mismatch, battery-backed data issue | ✅ High | Compare complete labels, revision, storage media, application, and network settings | Confirm approved interchangeability before field installation |
Support note: Contact technical support with photos of the complete controller label, board revision, LED pattern, VME rack slot, software/storage media, Ethernet configuration, boot messages, and Mark VI diagnostic logs.
Frequently Asked Questions (FAQ)
What is the GE IS215UCVEM08?
The IS215UCVEM08 is a GE Mark VI UCVE controller and PC control module used in Speedtronic turbine-control applications. It is a VME processor board, not a conventional analog or digital I/O module.
What processor and memory does it use?
Supplier documentation commonly identifies an Intel Celeron 300 MHz processor and 32 MB of DRAM. Because legacy UCVE assemblies can vary by revision or installed configuration, confirm the actual board markings and applicable GE manual before using those values as acceptance criteria.
What communication interfaces are available?
The listed interfaces are one 10BaseT/100BaseTX Ethernet port, two RS-232C ports labeled COM1 and COM2, an SVGA service-monitor connection, and keyboard/mouse service connections. Confirm the physical connector arrangement on the exact unit before purchase.
Is the IS215UCVEM08 interchangeable with UCVE08A?
Some suppliers list UCVE08A as an alternate reference, but that does not prove universal interchangeability. Compare hardware revision, processor and memory configuration, storage media, QNX image, Mark VI application, rack position, and network configuration before substitution.
Can I hot-swap the ?
Do not assume hot swapping is permitted. The controller executes turbine-control software, and removing it can cause loss of control, diagnostics, or redundancy. Follow the GE Mark VI maintenance procedure and the plant’s approved isolation and transfer process before removing the board.
Will a replacement include the turbine-control software?
Not necessarily. A surplus or refurbished board may include a blank, damaged, outdated, or site-specific storage image. Confirm whether the CompactFlash or other storage media is included, whether the correct QNX/Mark VI image is installed, and whether configuration backup and restoration are part of the supply.
Is this controller obsolete?
The belongs to the legacy GE Mark VI platform and is generally sourced through surplus, refurbished, repair, or exchange channels. Request the exact part-number photo, board revision, software status, battery condition, functional test report, warranty, and return terms before purchasing.
