Description
Core Product Summary
The GE VMIVME-5565 (also known as VME-5565) is an ultrahigh-speed fiber-optic Reflective Memory module for the VMEbus. It enables deterministic, low-latency data sharing across distributed real-time systems by automatically replicating memory writes to all nodes on the network.
The board is a 6U VME single-slot module that supports up to 256 nodes. It offers 64 MB or 128 MB of onboard SDRAM Reflective Memory and achieves network transfer rates from 43 MB/s to 174 MB/s depending on packet size. The fiber-optic link operates at 2.12 Gbaud and requires no host processor involvement for network operation.
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Product Type | Fiber-Optic Reflective Memory Module |
| Form Factor | 6U VME single slot |
| Bus Interface | VMEbus A24/A32, D08/D16/D32 |
| Network Speed | 2.12 Gbaud serial fiber-optic |
| Memory Options | 64 MB or 128 MB SDRAM Reflective Memory |
| Max Nodes | 256 |
| Packet Size | Dynamic 4 to 64 bytes |
| Network Throughput | 43 MB/s (4-byte) to 174 MB/s (64-byte packets) |
| Fiber Options | Multimode (up to 300 m) or Single-mode (up to 10 km) |
| Interrupts | Four general-purpose network interrupts with 32-bit data |
| DMA | Supported |
| Operating System Support | Windows, VxWorks, Linux |
Detailed Product Overview
The VMIVME-5565 implements Reflective Memory technology, in which data written to the local onboard SDRAM is automatically broadcast over the fiber-optic network and written into the corresponding memory locations on every other node. This creates a shared memory space that appears local to each system while remaining hardware-synchronized across the network.
Because the replication is performed entirely by the board hardware, there is no protocol stack overhead and no ongoing involvement of the host processor. Transmit and receive FIFOs buffer data during peak traffic to maintain high sustained throughput. The module supports dynamic packet sizing from 4 to 64 bytes, allowing optimization between latency and bandwidth.
The fiber-optic interface uses LC connectors and is available in multimode or single-mode versions. Multimode supports distances up to 300 m; single-mode extends reach to 10 km. The network can be configured in ring or star topologies and is fully interoperable with other members of the 5565 Reflective Memory family (PMC, PCI, and PCI Express versions).
Four general-purpose network interrupts allow any node to interrupt any other node (or all nodes) with a single command, each carrying 32 bits of user data. Error detection and an optional redundant transfer mode provide additional data integrity.
The board is widely used in hardware-in-the-loop (HIL) simulation, flight and vehicle simulation, distributed real-time control, radar and signal processing, and other applications that require deterministic, low-latency shared data.

VMIVME-5565
System Compatibility & Integration Requirements
| Item / Dependency | Verified Compatibility or Requirement | Practical Note |
|---|---|---|
| Backplane | Standard 6U VME | Single-slot installation |
| Memory Configuration | 64 MB or 128 MB options | Selected at order time |
| Fiber Type | Multimode or Single-mode | Must match network design |
| Network Size | Up to 256 nodes | Ring or star topology |
| Other 5565 Family | PMC-5565, PCI-5565, PCIe variants | Fully interoperable |
| Host Involvement | None required for network operation | Transparent shared memory |
| Operating Systems | Windows, VxWorks, Linux | Drivers available |
| Power | Supplied by VME backplane | Standard VME power rails |
Dimensions, Mounting & Connection Notes
The module is a standard 6U VME Eurocard that installs in a single slot of a VME chassis. The front panel provides the fiber-optic LC transceiver and status LEDs. All Reflective Memory data transfers occur over the fiber network; the VMEbus is used only for local host access to the onboard memory and control registers. Proper fiber cable type, length, and polarity must be observed, and the network must be correctly terminated according to the chosen topology.
FAQ
What is the GE VMIVME-5565?
It is a 6U VME Reflective Memory module that provides high-speed, deterministic shared memory over a fiber-optic network.
How does Reflective Memory work?
Data written to the local memory on one node is automatically written to the corresponding memory on all other nodes by hardware, with no host processor involvement.
What is the maximum network size?
Up to 256 nodes.
What transfer rates are supported?
Network throughput ranges from 43 MB/s (4-byte packets) to 174 MB/s (64-byte packets).
What fiber options are available?
Multimode fiber (up to 300 m) and single-mode fiber (up to 10 km).
Does it require special software?
No. Once configured, applications simply read and write the local Reflective Memory as if it were ordinary local RAM.
Is it compatible with other form factors?
Yes. It interoperates with PMC, PCI, and PCI Express versions of the 5565 Reflective Memory family.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626