Description
Key Technical Specifications
- Module Type: High-Level Analog Input FTA (Field Termination Assembly)
- Input Signal Range: 1 to 5 V DC / 4 to 20 mA interface compatible
- Channel Capacity: 16 differential analog input channels
- IOP Interface: Ribbon cable connection to Analog Input IOP
- Isolation: Channel-to-channel optical/galvanic isolation
- Operating Temperature: −40 to +70 °C
- Storage Temperature: −40 to +85 °C
- Relative Humidity: 0% to 95% non-condensing
- Mounting Type: DIN rail or surface cabinet mounting plate
- Dimensions: 205 mm x 120 mm x 50 mm
- Weight: 0.53 kg
Product Introduction
The Honeywell MC-TAIH02 (51304453-150) is a high-level analog input Field Termination Assembly designed for Honeywell TDC 3000 and TPS control systems. It serves as the physical marshaling interface between field-mounted process transmitters (pressure, flow, temperature, and level) and the central Analog Input Input/Output Processor (IOP).
Maintenance teams deploy this assembly during legacy system sustainment and hardware overhauls. It maintains signal integrity while isolating sensitive controller backplanes from field-induced electrical transients and industrial noise loops.

MC-TAIH02

MC-TAIH02
Installation & Configuration Guide
Stage 1: Pre-Installation Preparation
- ⚠️ Safety First: Notify operations of potential control loop interruption, verify the loops are shifted to manual control mode, execute Lock Out/Tag Out (LOTO) on loop power feeds, and allow power to bleed down completely.
- Tools Required: ESD grounding wrist strap, #1 and #2 flat-head screwdrivers, Digital Multimeter (Fluke 115 or equivalent), wire labels, reference camera.
- Data Backup: Document current loop assignments in TDC 3000 engineering configuration tools, map physical terminal numbers, and photograph ribbon cable orientations.
Stage 2: Removing the Old Module
- Verify loop power is dropped to prevent floating voltage spikes across analog pairs.
- Label every field signal wire meticulously before unseating them from the screw terminals.
- Unplug the multi-conductor ribbon cable connecting the FTA to the Analog Input IOP. Do not pull on the ribbon wiring itself.
- Release the mounting clips or screws securing the base assembly and lift it off the panel backplate.
- Self-Check: Confirm all wires are labeled clearly. Leave the old FTA housing accessible until the new unit is verified.
Stage 3: Installing the New Module
- Ground yourself using an ESD wrist strap and verify the replacement part number suffix matches your exact system spec.
- Terminal Mapping: Secure the MC-TAIH02 onto the cabinet mounting surface or DIN rail brackets, torque mounting fasteners appropriately.
- Reconnect the system ribbon cable from the Analog Input IOP to the FTA header, ensuring the polarization key aligns without bending pins.
- Terminate field wires back to their respective screw clamp locations, maintaining shielding continuity and proper drain-wire grounding.
- Self-Check: Pull gently on each termination screw block to confirm the wire grip is solid and mechanical latching is secure.
Stage 4: Power-On & Testing
- Pre-Power Check: Measure loop resistance across terminals using a multimeter to verify there are no inadvertent short circuits or ground faults on the 4-20 mA current loops.
- Power-On Steps:
- Re-energize the loop power supplies and controller cabinet racks.
- Check local module health indicators or controller node status logs.
- Access the TDC 3000/TPS station interface to verify channel health and confirm live process variable readings match field conditions.
- Perform a loop calibration check with an instrument calibrator if required for safety-critical loops.
- ⚠️ Troubleshooting Note: If an analog channel reads a zero or scale error, check the ribbon cable seating, verify loop power supply fusing, and confirm that the field transmitter loop wiring polarity is correct.
Frequently Asked Questions (FAQ)
Can this FTA be hot-swapped under power?
Honestly, while the terminal block side handles passive field signals, hot-swapping the system ribbon cable connecting to the live Analog Input IOP can inject voltage transients or crash the analog acquisition cycle. It is always safest to drop loop power or take the logical point offline before touching internal system cables.
Is this model obsolete, and is it genuinely new?
Honeywell TDC 3000 hardware relies on mature component lifecycles, meaning direct factory replacements can have extended procurement cycles. Units designated as “New Original” or “New Surplus” are authentic factory-manufactured stock that have never been put into active service, acquired from excess plant reserves or verified surplus inventories.
What is the direct replacement if this exact model is out of stock?
You must match the exact part number (MC-TAIH02 / 51304453-150). Because FTA pinouts, form factors, and ribbon cable headers are specifically mapped to legacy TDC 3000 IOP configurations, attempting an unverified substitution will break cabinet wiring geometry.
Will I lose my configuration logic when I swap this FTA?
No. The MC-TAIH02 is a passive Field Termination Assembly containing terminal blocks, resistors, and routing traces—it has no onboard processor or retentive memory storage. The configuration logic and scaling parameters reside strictly within the TDC 3000 controller database.
Why is your price lower than the OEM factory list price?
Surplus automation providers source excess parts from facility upgrades, plant modernizations, and reserved warehouse stock. Bypassing traditional multi-tier OEM channels allows us to offer immediate hardware availability to maintenance groups at a fraction of legacy manufacturer markups.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626