Description
Core Product Summary
The Kollmorgen PRD-B040EAIZ-33 is a digital servo drive amplifier from the SERVOSTAR CD product series, identified on the unit as type CE03550. It converts fixed-frequency mains power into regulated three-phase current for brushless servomotors, closing the current, velocity, and position loops inside the amplifier so the host controller only has to supply the motion command.
The “Z” position in the order code denotes the resolver feedback configuration, and the unit uses an analog command interface, so it is intended for installations where the axis is commanded by a ±10 V velocity or torque reference from a PLC or motion controller rather than a digital fieldbus. Setup, tuning, and parameter backup are handled through Kollmorgen’s MOTIONLINK Windows software over the drive’s serial interface. As a SERVOSTAR CD component it is designed for vertical panel mounting inside a protective electrical enclosure, with defined side clearance between adjacent drives and EMI filtering required on the input power leads.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer / Series | Kollmorgen, SERVOSTAR CD digital servo amplifier series |
| Order code | PRD-B040EAIZ-33 |
| Unit type designation | CE03550 |
| Product function | Closed-loop control of brushless servomotors (current, velocity, and position loops) |
| Feedback type | Resolver (per the “Z” feedback position in the order code) |
| Command interface | Analog command interface, ±10 V reference level of the SERVOSTAR CD analog input |
| Setup / configuration software | MOTIONLINK (Windows-based) |
| Commutation method | Sinusoidal commutation |
| Mounting | Vertical panel mounting inside an electrical enclosure |
| Installation spacing | Approximately 12.7 mm (0.5 in) side clearance between adjacent units |
| EMC basis | Series tested for radiated/conducted emissions and immunity per EN 55081-2 / EN 55082-2 (heavy industrial environment) |
Engineering Selection Highlights
- Resolver feedback (“Z” code position) → the drive hardware is built to read a motor-mounted resolver, not an encoder. Verify the motor’s feedback device matches before ordering; resolver, incremental encoder, and sine encoder versions of the SERVOSTAR CD platform are different hardware configurations.
- Analog command interface → the axis must be driven by an analog velocity or torque reference from a controller. Systems that command axes over a digital network need a different interface variant of the platform.
- CE03550 type designation → the unit’s nameplate maps this order code to the CE03550 amplifier configuration; when replacing a failed drive, matching both the order code and the nameplate type avoids fitting an interface or feedback variant with different behavior.
- MOTIONLINK software dependency → motor data setup, loop tuning, parameter backup, and monitoring are performed through Kollmorgen’s MOTIONLINK environment on Windows over the serial port, so commissioning requires a PC and the appropriate cable/adapter for the drive’s serial interface.
- Enclosure installation → SERVOSTAR CD units are panel-mount components intended for installation inside a protective electrical enclosure, not on an open machine frame.
- EMI input filtering → the amplifier series requires EMI filtering in the input power leads to meet conducted-emission limits for the industrial environment; retrofit installations must include a suitable line filter.
- Adjacent-unit clearance → approximately 12.7 mm of free space between mounted drives is specified for ventilation, which constrains multi-axis cabinet layout.

PRD-B040EAIZ-33

PRD-B040EAIZ-33
System Compatibility & Integration Requirements
| Item / Dependency | Verified Compatibility or Requirement | Practical Note |
|---|---|---|
| Motor type | Brushless AC servomotors | The amplifier regulates three-phase current to brushless servomotors with sinusoidal commutation. |
| Motor feedback | Resolver (per order code “Z”) | Match the motor’s feedback device to the drive’s feedback hardware; encoder and sine-encoder versions are separate configurations. |
| Command source | Analog interface (±10 V reference level) | Driven by a velocity or torque command from a PLC or motion controller. |
| Configuration tool | MOTIONLINK software environment for Windows | Required for motor parameter setup, tuning, monitoring, and parameter backup. |
| Power input | Requires EMI filtering on input power leads | Needed to meet conducted-emission requirements for the industrial environment. |
| Mounting orientation | Vertical panel mounting | Units are designed for back-panel installation inside an electrical enclosure. |
| Multi-drive layout | ~12.7 mm (0.5 in) side clearance between units | Apply when several amplifiers share a panel. |
Dimensions, Mounting & Connection Notes
SERVOSTAR CD amplifiers are designed for back-panel assembly inside an electrical enclosure, mounted vertically and spaced approximately 12.7 mm (0.5 in) apart from adjacent units to allow proper ventilation. Because these products are electronic panel components rather than IP-rated machine-side devices, the enclosure provides the physical and environmental protection. Input power leads require EMI filtering to meet the series’ conducted-emission limits. Grounding of the amplifier housing is a documented installation requirement.
Detailed Product Overview
The PRD-B040EAIZ-33 belongs to Kollmorgen’s SERVOSTAR CD family of digital servo amplifiers. The platform is built as a digital replacement for analog servo amplifiers: instead of an analog power stage whose gain depends on hardware trimming, the SERVOSTAR CD digitizes the command and feedback signals and executes the control loops in firmware, with a Windows software environment (MOTIONLINK) used to load motor data, tune the loops, and store the configuration.
Two characteristics of this specific order code matter most when matching it to an installation. First, the feedback hardware is the resolver version. Resolvers are robust electromagnetic position sensors, and the drive’s resolver input determines which motors the unit can commutate: a motor fitted with an incremental encoder or sine encoder needs the corresponding interface variant, so the feedback device on the machine’s motor is the first thing to check. Second, the command interface is analog. In practice this means the controller provides a ±10 V-style reference and the drive is responsible for all loop closure — a division of labor common in older motion systems and in retrofit cabinets where the motion controller is retained and only the amplifier is replaced.
Integration also carries two infrastructure requirements that are easy to overlook at procurement time. The amplifier needs EMI filtering on its input power leads to comply with the series’ conducted-emission limits, so a cabinet that was originally built without a line filter will need one added. And because the unit is a panel-mounted component with defined ventilation clearance, replacement planning in a full cabinet should confirm that the footprint and the approximately 12.7 mm side spacing can be honored.
Commissioning is software-driven: motor parameters, loop tuning, and diagnostics are handled in MOTIONLINK, and the drive stores its configuration so a swapped unit can be restored from a backed-up parameter set. For maintenance teams this is the practical replacement procedure — record the MOTIONLINK configuration of a working axis before a failure occurs, so an identical order code can be brought online quickly.
Applications & System Role
Within a machine architecture, the PRD-B040EAIZ-33 sits between the mains supply and a single brushless servomotor axis. It receives an analog velocity or torque reference from the supervising controller, reads rotor position from the motor’s resolver, and modulates phase current so the axis follows the commanded profile. The current, velocity, and position loops execute in the amplifier, so the host controller is relieved of high-speed loop processing.
This type of analog-commanded, resolver-feedback axis amplifier is a natural fit for machine retrofits and multi-axis cabinets where the existing controller outputs ±10 V references, and where the drive must be reconfigured to a different motor by loading motor data via MOTIONLINK. It is a system component of the SERVOSTAR CD platform, which Kollmorgen positions for general industrial servo applications.
FAQ
What is the Kollmorgen PRD-B040EAIZ-33?
It is a digital servo drive amplifier from the SERVOSTAR CD series, nameplate-designated CE03550, used for closed-loop control of brushless servomotors.
Which feedback does it use?
The “Z” position in the order code identifies the resolver feedback configuration; the drive reads motor position from a resolver rather than an encoder.
How is the drive commanded?
Through its analog command interface, accepting a velocity or torque reference from a PLC or motion controller.
What software is needed to set it up?
Kollmorgen’s MOTIONLINK environment for Windows, connected via the drive’s serial interface, is used for motor data setup, tuning, monitoring, and parameter backup.
How must it be mounted?
Vertically on a panel inside a protective electrical enclosure, with approximately 12.7 mm (0.5 in) of side clearance between adjacent units for ventilation.
Does the drive need external components on the power input?
Yes — the SERVOSTAR CD series requires EMI filtering in the input power leads to meet conducted-emission requirements for the industrial environment.
What should be checked before using it as a replacement drive?
Confirm the motor’s feedback device is a resolver, that the controller provides an analog command signal, and that the nameplate type designation matches the unit being replaced, since the platform exists in several interface and feedback variants.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626