Sale!

Motorola MVME55006E-0161R 1 GHz MPC7457 VME SBC

  • Model: MVME55006E-0161R
  • Brand: Motorola / Emerson
  • Series: MVME5500 6E VMEbus Single-Board Computers
  • Core Function: High-performance embedded VME computing
  • Product Type: 6U VMEbus Single-Board Computer (SBC)
  • Key Specs: 1 GHz MPC7457 PowerPC, 512 MB ECC SDRAM, dual 64-bit PCI/PMC buses
  • ⚠️ Obsolete Model – Limited Stock Available
  • Condition: New Original / New Surplus
Categories: , , , , SKU: MVME55006E-0161R Brand:

Description

Key Technical Specifications

Parameter Value
Processor Motorola/Freescale MPC7457 PowerPC
Processor speed 1 GHz
L1 cache 32 KB instruction / 32 KB data
L2 cache 512 KB on-chip
L3 cache 2 MB external DDR SRAM
Vector processing AltiVec coprocessor
Main memory 512 MB 133 MHz ECC SDRAM
Memory expansion 512 MB additional memory via RAM5500 mezzanine, up to 1 GB total
Flash memory 40 MB total: 32 MB soldered Flash plus 8 MB socketed Flash
VMEbus interface VME64, A32/D32/D64, via Tundra Universe II
PCI architecture Two independent 64-bit PCI buses, 33/66 MHz
PMC expansion Two IEEE P1386.1 PMC slots, 33/66 MHz capable
PCI expansion 64-bit PCI expansion mezzanine connector
Ethernet One 10/100/1000Base-T port plus one 10/100Base-TX port
Serial ports Two configurable RS-232/RS-422/RS-485 ports
System controller Marvell GT-64260B host bridge
Front panel Standard handles; 6E extended-temperature variant
Form factor 6U VME, single slot even with PMC modules installed

The MVME55006E-0161R is a 6E variant of the MVME5500 family, configured with a 1 GHz MPC7457 PowerPC processor, 512 MB ECC SDRAM, standard handles, and extended-temperature capability. It provides 512 KB on-chip L2 cache, 2 MB L3 cache, dual 64-bit 33/66 MHz PCI buses, two PMC sites, Gigabit Ethernet, and a second 10/100 Ethernet port.

 

Product Introduction

The Motorola MVME55006E-0161R is a 6U VMEbus single-board computer built for data-intensive embedded control, test, communications, and industrial-automation systems. Its MPC7457 processor, ECC memory, dual PCI buses, and PMC expansion provide a high-performance service platform for existing Motorola VME installations.

The “6E” designation identifies the extended-temperature version, while “-0161R” specifies the 1 GHz MPC7457, 512 MB ECC SDRAM, and standard-handle configuration. The board remains a single VME slot even when populated with two PMC modules, which helps preserve chassis space during replacement or system upgrades.

MVME55006E-0161R

MVME55006E-0161R

MVME55006E-0161R

MVME55006E-0161R

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
No LEDs on power-up Chassis power, fuse, backplane fault, or poor P1/P2 seating ❌ Low Measure +5 V and +3.3 V at the VME backplane; reseat the board with power off Check PSU, fuses, and connector seating before replacing the SBC
Board powers up but does not boot Corrupt Flash, failed boot device, or firmware/configuration fault ✅ High Connect to the serial debug port and capture the boot messages Restore firmware or boot image; replace the board if Flash is damaged
No Ethernet link Cable, switch port, PHY configuration, or driver issue ❌ Low Swap cable and switch port; verify link LEDs and IP settings Test both Ethernet ports before condemning the board
VME communication timeout VME address map, terminator, bus grant, or master/slave configuration mismatch ✅ High Inspect VME jumpers and confirm the address map against system documentation Correct configuration first; do not assume the board is failed
PMC module not recognized PMC seating, PCI bus configuration, or incompatible PMC card ❌ Low Power down, reseat PMC, and test it in another known-good MVME55006E system Verify PMC compatibility and PCI bus settings
ECC memory errors or random resets Weak RTC battery, overheating, poor contact, or failing SDRAM ✅ Medium Check battery voltage, clean contacts, verify airflow, and run memory diagnostics Replace the board if ECC errors persist after environmental checks
Intermittent operation after installation ESD damage, bent pins, or incomplete connector engagement ✅ High Inspect P1/P2 and PMC connectors; reseat with ESD protection Replace only after connector, power, and configuration checks pass

If the fault remains unresolved, send photos of the board and chassis, jumper settings, serial boot output, and diagnostic logs before ordering a replacement.

 

Frequently Asked Questions

Can I hot-swap the MVME55006E-0161R?
No. Power down the VME chassis before removing or installing the board. This is a conventional VME processor module, not a hot-swap design. Use a grounded ESD wrist strap and avoid touching connector pins or components.

Is the MVME55006E-0161R obsolete?
Yes. Motorola originally produced the MVME5500 series, and the product line later passed through Emerson ownership. Original manufacturing has ended, so dependable supply generally comes from controlled surplus or tested refurbished inventory.

What does the “6E” suffix mean?
The 6E suffix identifies the extended-temperature version of the MVME5500 family. The -0161R suffix identifies a 1 GHz MPC7457 processor, 512 MB ECC SDRAM, and standard-handle configuration.

Will it directly replace an MVME5500-0161?
Often yes at the board level, but verify the processor type, memory capacity, front-panel handle style, firmware/boot image, VME address map, and installed PMC hardware. The 6E version is intended for extended-temperature applications, so confirm that this matches your installation requirements.

Will my application software remain after a board swap?
Not automatically. The application may reside in Flash, NVRAM, a PMC storage module, or another device in the VME chassis. Back up the boot image, application files, network settings, and VME configuration before removing the old board.

Why is this surplus board less expensive than a new OEM unit?
Because Motorola no longer manufactures it, pricing reflects available surplus inventory rather than current OEM production. New Surplus stock is unused original product; it may have older date codes but should not have field-operating hours.

What should I check before ordering?
Confirm the required 1 GHz MPC7457 configuration, 512 MB ECC SDRAM, standard-handle style, PMC cards, VME system-controller role, firmware/boot image, and chassis power budget. The MVME55006E-0161R supports up to 1 GB total ECC SDRAM when the RAM5500 memory mezzanine is used.