Sale!

NI-9234 4-Channel Sound and Vibration Module

  • Manufacturer: National Instruments (NI)
  • Model: NI-9234
  • Product type: C Series sound and vibration input module
  • Input channels: 4 differential analog input channels
  • Resolution: 24-bit ADC
  • Input range: ±5 V
  • Maximum sampling rate: 51.2 kS/s per channel
  • Sensor support: IEPE and non-IEPE sensors, including compatible accelerometers, microphones, tachometers, and TEDS sensors
  • Signal conditioning: Software-selectable AC/DC coupling and switchable IEPE excitation
  • Platform: NI C Series; verify chassis and software compatibility before purchase
  • Product variants: NI lists part numbers 783440-01, 779680-01, and 779680-03; the latter is listed as conformal-coated. Availability and support status vary by part number.
Categories: , , , , SKU: NI-9234 Brand:

Description

Key Technical Specifications

Parameter Specification
Manufacturer National Instruments (NI)
Model NI-9234
Product family C Series
Measurement type Sound and vibration input
Analog input channels 4 differential channels
ADC resolution 24 bits
Input voltage range ±5 V
Maximum sampling rate 51.2 kS/s per channel
Sampling mode Simultaneous
ADC architecture Delta-sigma with analog prefiltering
Input coupling Software-selectable AC/DC
IEPE excitation Software-selectable; 2.0 mA minimum, 2.1 mA typical
IEPE compliance voltage 19 V maximum
Sensor compatibility Compatible IEPE and non-IEPE accelerometers, microphones, tachometers, and TEDS sensors
Connector BNC; connector arrangement varies by part number
Input impedance 305 kΩ differential
Channel isolation No channel-to-channel or channel-to-earth isolation
Overvoltage protection ±30 V for signal source connected across AI+ and AI−
Power consumption 900 mW maximum in active mode
Operating temperature −40°C to +70°C
Storage temperature −40°C to +85°C
Operating humidity 10–90% RH, noncondensing
Ingress protection IP40
Weight 173 g
Recommended calibration interval 1 year

Source: NI’s official specifications and product documentation. The overvoltage-protection rating is not a permissible continuous measurement range; the normal input range remains ±5 V.

 

Product Introduction

The NI-9234 is designed for dynamic signal acquisition where vibration, acoustic response, or rotating-equipment behavior must be measured across multiple channels at the same time. Its 24-bit analog-to-digital conversion, 51.2 kS/s-per-channel sampling rate, and software-selectable IEPE excitation support measurements from compatible industrial sensors. Integrated anti-aliasing filters adjust to the configured sampling rate, helping preserve in-band signal information for frequency analysis and condition monitoring. System integration requires a compatible NI C Series chassis and supported software configuration.

 

Installation & Configuration Guide

Verify the hardware platform

  • Confirm the NI-9234 part number and connector configuration.
  • Check the NI C Series chassis or controller compatibility matrix before installation.
  • Verify that the selected driver and programming mode support the intended acquisition system. Compatibility can differ by chassis and controller.

Prepare the measurement system

  • Power down the chassis according to its operating instructions before installing or removing the module.
  • Confirm that the sensor output and expected signal levels fall within the NI-9234’s ±5 V input range.
  • Do not connect signals from mains circuits or higher measurement categories that exceed the module’s safety ratings.

Connect the sensors

  • Connect each sensor to the appropriate BNC input.
  • Select AC coupling or DC coupling based on the measurement requirements.
  • Enable IEPE excitation only for sensors that require it.
  • For grounded signal sources, follow NI’s wiring guidance to minimize ground-related measurement errors.
  • Keep BNC connector shells from contacting each other, the module, or the chassis where this could introduce unwanted ground noise.

Configure acquisition

  • Configure the module in the applicable NI software environment.
  • Set the sampling rate, coupling mode, and IEPE excitation for each channel as required.
  • Check the selected rate against the module’s supported data-rate range.
  • For synchronized measurements across multiple modules, verify the master-timebase arrangement and synchronization requirements.

Validate the measurement

  • Acquire a test signal and confirm that all four channels return plausible values.
  • Check sensor bias, signal clipping, channel noise, and expected frequency content.
  • Verify calibration status if the measurement is used for maintenance decisions or engineering acceptance.
  • Record the module part number, sensor configuration, acquisition settings, and calibration date.

Important limitation: The NI-9234 does not support direct analog or digital triggering by itself. A supported additional triggering module or platform-specific acquisition method may be needed for trigger-based applications.

NI-9234

NI-9234

NI-9234

NI-9234

Frequently Asked Questions

Q1: What is the NI-9234 used for?

It acquires sound and vibration signals from compatible sensors, including accelerometers and microphones. Typical applications include machinery condition monitoring, vibration analysis, and acoustic measurements.

Q2: How many channels does the NI-9234 have?

It has four differential analog input channels that sample simultaneously.

Q3: Can it power an IEPE accelerometer?

Yes. The module provides software-selectable IEPE excitation with a specified minimum current of 2.0 mA and a typical current of 2.1 mA. Confirm that the sensor’s current and compliance-voltage requirements are compatible.

Q4: What is the maximum sampling rate?

The maximum rate using the internal master timebase is 51.2 kS/s per channel. The supported rate range depends on the timebase configuration.

Q5: Is the NI-9234 isolated?

No. NI specifies no channel-to-channel or channel-to-earth isolation. The module is not intended for direct measurement of mains circuits or signals requiring higher measurement-category protection.

Q6: Are all NI-9234 part numbers identical?

No. NI lists multiple orderable part numbers, including 783440-01, 779680-01, and 779680-03. The 779680-03 variant is listed as conformal-coated, while 783440-01 is described as an OEM module. Check connector arrangement, coating, mechanical integration, and support status before ordering.

Q7: What should be checked when replacing an NI-9234?

Verify the exact part number, connector type, chassis compatibility, sensor requirements, software support, and calibration needs. If the application depends on synchronized measurements or triggering, confirm those requirements separately rather than assuming they are supported by the module alone.