Sale!

Novotron ND32-5610 SPSV 3.2 92A8100263 Digital Servo Drive

  • Model: ND32-5610
  • Firmware / Configuration: SPSV 3.2
  • Manufacturer Part Number: 92A8100263
  • Brand: Novotron
  • Series: ND32 servo converter / servo drive family
  • Core Function: Closed-loop servo motion control
  • Product Type: Digital servo drive / servo converter module
  • Key Specs: Speed, position, and torque control; configuration-dependent AC input; SPSV 3.2 firmware
  • ⚠️ Obsolete Model – Limited Stock Available
  • Condition: New Original / New Surplus
Categories: , , , , SKU: ND32-5610 SPSV 3.2 92A8100263 Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer Novotron Elektronik / Novotron Industrie-Automation
Base model ND32-5610
Firmware baseline SPSV 3.2
Manufacturer part number 92A8100263
Product family ND32 digital servo converter
Control modes Speed, position, and torque control
Motor compatibility Synchronous servo motors and asynchronous servo motors, configuration-dependent
Closed-loop control Encoder-based speed, position, and torque regulation
Communication Configuration-dependent; CANopen, Modbus, and EtherCAT may apply
Protection functions Overcurrent, overload, overvoltage, and overtemperature protection
Operating temperature Approximately -10 to +50°C or -10 to +60°C, configuration-dependent
Cooling Natural or forced-air cooling, configuration-dependent
Installation Cabinet / rack-mounted servo drive module
Verification requirement Match ND32-5610, SPSV 3.2 firmware, and 92A8100263 before installation

The ND32-5610 is a Novotron digital servo converter used for closed-loop speed, position, and torque control of servo motors. Supplier listings associate the SPSV 3.2 / 92A8100263 configuration with this ND32-5610 servo-drive family.

 

Product Introduction

The Novotron ND32-5610 SPSV 3.2 is a digital servo drive module used in industrial automation, robotics, CNC machinery, packaging equipment, and other motion-control systems. It regulates servo-motor speed, position, and torque through closed-loop control.

The SPSV 3.2 designation identifies the firmware/configuration baseline, while 92A8100263 is the associated Novotron part number. Because ND32-5610 variants can differ in power stage, encoder interface, communication option, and firmware, buyers should match all three identifiers before installing this unit as a replacement.

 ND32-5610 SPSV 3.2 92A8100263

ND32-5610 SPSV 3.2 92A8100263

 ND32-5610 SPSV 3.2 92A8100263

ND32-5610 SPSV 3.2 92A8100263

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Drive does not power up Control power, main power, fuse, DC bus, or wiring fault ❌ Low Measure control and main input voltages; inspect fuses and DC-bus terminals Check power supply and wiring before replacing the drive
Drive powers up but motor does not turn Enable signal missing, command source inactive, encoder fault, or parameter error ✅ High Verify enable I/O, command source, encoder feedback, and active fault code Correct enable/command/encoder issues before condemning the drive
Servo fault or drive trips Overcurrent, overload, overvoltage, overtemperature, or encoder fault ✅ High Read the drive fault code and check motor current, DC-bus voltage, cooling, and encoder cable Clear the root cause; repeated trips usually indicate a system issue, not only a failed drive
Motor runs erratically Incorrect encoder wiring, poor grounding, EMI, or wrong drive parameters ✅ High Inspect encoder shield/grounding, verify motor feedback, and compare parameter set Correct wiring and parameters before replacing hardware
Position error or poor accuracy Encoder coupling slip, mechanical backlash, gain tuning, or feedback fault ✅ Medium Check mechanical coupling, run a low-speed positioning test, and review servo gains Isolate mechanical versus electrical causes before replacing the drive
No communication with PLC Baud rate, node address, protocol mismatch, or cable/shielding fault ✅ High Verify CANopen/Modbus/EtherCAT settings, termination, and cable continuity Match communication configuration before replacing the drive
Overtemperature shutdown Blocked airflow, failed fan, high ambient temperature, or excessive load ✅ High Inspect heatsink and fan, measure ambient temperature, and review load duty cycle Improve cooling or reduce load; replace the drive only if cooling is verified

If the fault remains unresolved, send photos of the drive nameplate, firmware display, fault code, motor nameplate, encoder wiring, and parameter backup before ordering a replacement.

 

Frequently Asked Questions

Can I hot-swap the Novotron ND32-5610?
No. Disconnect control power, main power, and motor power before removal or installation. Servo drives can retain hazardous DC-bus voltage after shutdown; allow the bus to discharge and verify it with a meter before handling.

Is the ND32-5610 SPSV 3.2 obsolete?
Yes. The ND32-5610 is a legacy Novotron servo-drive family, and SPSV 3.2 is an older firmware/configuration baseline. Current supply is generally limited to New Surplus, refurbished, or tested service-exchange inventory.

What does SPSV 3.2 mean?
SPSV 3.2 identifies the firmware/configuration baseline associated with this ND32-5610 unit. Do not assume that another SPSV version is directly interchangeable; firmware differences can affect parameters, safety functions, and system communication.

Will it directly replace another ND32-5610 variant?
Only after matching the full model suffix, SPSV firmware version, 92A8100263 part number, power rating, encoder interface, and communication configuration. ND32-5610 variants are not necessarily parameter- or pin-compatible.

Will my servo parameters remain after replacement?
Not automatically. Parameter sets, homing data, gain settings, and motion profiles may reside in the drive or the upstream controller. Back up the complete parameter set and configuration before removing the old drive.

Why is this surplus drive less expensive than a new OEM unit?
Because Novotron no longer supplies it as standard new production, pricing reflects available surplus inventory rather than current OEM manufacturing. New Surplus stock is unused original product; it may have older date codes but should not have field-operating hours.

What should I check before ordering?
Confirm the exact ND32-5610 suffix, SPSV 3.2 firmware requirement, 92A8100263 part number, motor type and power, encoder type, control mode, communication protocol, and cabinet cooling capacity. The ND32 family documentation should remain the final authority for electrical ratings and installation limits.