Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Model | MVI56E-PDPMV1 |
| Manufacturer | ProSoft Technology |
| Compatible platform | Rockwell Automation ControlLogix 1756 chassis |
| Function | PROFIBUS DP-V1 master network scanner for ControlLogix processors |
| Chassis slots required | 1 |
| PROFIBUS role | PROFIBUS DP Class 1 Master, DP-V0 and DP-V1 |
| PROFIBUS interface | Optically isolated RS-485, DB-9 female connector |
| PROFIBUS baud rates | 9.6 kbps to 12 Mbps, all standard PROFIBUS rates |
| Maximum slave devices | Up to 125 slaves with repeaters |
| Maximum cyclic input data | 1,536 bytes |
| Maximum cyclic output data | 1,536 bytes |
| Acyclic services | DP-V1 Class 1 and Class 2 read/write services |
| PROFIdrive support | PROFIdrive 3.1-compliant parameter read/write operations |
| DP-V1 telegrams | Multicast and broadcast support |
| Configuration software | ProSoft Configuration Builder (PCB) |
| Diagnostic software | FDT/DTM PROFIBUS Master communication DTM |
| GSD support | Project-specific GSD file import library |
| Backplane current load | 800 mA at 5.1 V DC; 3 mA at 24 V DC |
| Operating temperature | 0 to +60°C |
| Storage temperature | −40 to +85°C |
| Relative humidity | 5% to 95%, non-condensing |
| Shock rating | 30 g operational; 50 g non-operational |
| Vibration rating | 5 g from 10 to 150 Hz |
| LED indicators | Operations, network communication, master token-hold, and network configuration |
| Hot-swap support | PROFIBUS DP slave devices can be hot-swapped |
| Backward compatibility | Compatible with legacy MVI56-PDPMV1 configuration files |
The MVI56E-PDPMV1 is the enhanced version of the MVI56-PDPMV1. It supports both cyclic I/O exchange and acyclic DP-V1 parameter access, allowing ControlLogix to communicate with PROFIBUS DP-V0 and DP-V1 slave devices.
Product Introduction
The ProSoft MVI56E-PDPMV1 is a single-slot PROFIBUS DP-V1 master module for Rockwell Automation ControlLogix 1756 chassis. It lets a ControlLogix PAC operate as a PROFIBUS DP Class 1 master, exchanging cyclic I/O data with drives, remote I/O, encoders, valve terminals, and field instruments.
It supports DP-V0 cyclic data exchange and DP-V1 acyclic read/write services, including PROFIdrive 3.1 parameter access. The module handles PROFIBUS bus scheduling, token rotation, and slave polling independently, then maps process data to the ControlLogix processor over the backplane.

MVI56E-PDPMV1

MVI56E-PDPMV1
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to this Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Module not recognized in Studio 5000 | Missing EDS file, wrong slot, or chassis configuration issue | ✅ High | Verify slot number, import the ProSoft EDS file, and confirm the module appears in the I/O tree | Correct chassis configuration before replacing the MVI56E-PDPMV1 |
| PROFIBUS network will not initialize | Wrong baud rate, duplicate master, missing termination, or GSD/configuration mismatch | ✅ High | Verify baud rate, master address, GSD files, termination resistors, and cable A/B polarity | Correct PROFIBUS configuration before replacing the module |
| One slave drops offline | Slave power loss, address conflict, cable fault, or device firmware issue | ❌ Low | Check slave LEDs and diagnostics; inspect its cable, address, and power supply | Troubleshoot the slave device and its cable first |
| Multiple slaves drop offline | Bus termination, repeater fault, shield/ground issue, or master configuration fault | ✅ High | Inspect bus termination, repeater status, shield continuity, and master diagnostic log | Correct bus topology and grounding before replacing the module |
| Cyclic I/O data does not update | Incorrect module configuration, I/O mapping, or ladder data-transfer logic | ✅ High | Verify GSD configuration, slave parameterization, backplane I/O mapping, and ladder MOV/COP instructions | Correct configuration and ladder logic before replacing hardware |
| DP-V1 parameter read/write fails | Device does not support DP-V1, wrong slot/index, or acyclic service not configured | ✅ Medium | Confirm slave DP-V1 capability and verify slot/index/address in the request | Use DP-V0 cyclic data or correct the DP-V1 request parameters |
| Drive will not start over PROFIBUS | PROFIdrive control-word/state-machine mismatch or drive fault | ❌ Low | Review PROFIdrive control word, status word, and drive fault buffer | Correct the PROFIdrive sequence and clear the drive fault |
| Module overheats | Excessive chassis load, blocked airflow, or high ambient temperature | ✅ Medium | Measure chassis temperature and verify the 800 mA at 5.1 V DC backplane load is included in the power budget | Improve cabinet cooling or redistribute chassis load |
❗ Do not assume the MVI56E-PDPMV1 has failed because one slave drops offline. A failed slave power supply, loose PROFIBUS connector, incorrect termination, or bad repeater is more common than a master-module fault.
If the fault remains after checking the EDS/chassis configuration, PROFIBUS cabling, termination, GSD files, slave diagnostics, and ladder I/O mapping, contact technical support with photos of the module, PROFIBUS network layout, PCB configuration, and Studio 5000 diagnostics.
Frequently Asked Questions
Can the MVI56E-PDPMV1 operate as a PROFIBUS slave?
No. It is a PROFIBUS DP-V1 Class 1 master module. It scans and manages DP-V0/V1 slave devices; use a PROFIBUS slave module if your ControlLogix system must appear as a slave on another master’s network.
How many PROFIBUS slaves can it support?
It supports up to 125 slave devices when the network uses repeaters. Verify the total bus length, segment loading, repeater count, and slave response requirements before building a large network.
Does it support DP-V1 acyclic communications?
Yes. It supports DP-V1 Class 1 and Class 2 read/write services for acyclic parameter data, as well as multicast and broadcast DP-V1 telegrams.
Can I use it with PROFIBUS PA devices?
Yes, indirectly. PROFIBUS PA slaves can be connected through DP/PA couplers or links. The MVI56E-PDPMV1 communicates with the DP side of the coupler/link, not directly with the MBP/PA physical layer.
Can I hot-swap PROFIBUS slaves?
Yes. The module supports hot-swapping of PROFIBUS DP slave devices. This does not mean you can hot-swap the MVI56E-PDPMV1 master module itself; follow a controlled removal procedure for the master.
Can I replace an MVI56-PDPMV1 with an MVI56E-PDPMV1?
The MVI56E-PDPMV1 is backward compatible with legacy MVI56-PDPMV1 configuration files, but verify the EDS file, firmware, GSD library, and Studio 5000 I/O configuration before migration. Do not assume an identical replacement without validating the existing project.
Why is New Surplus less expensive than factory-new stock?
New Surplus means genuine ProSoft inventory manufactured earlier but not installed or commissioned. We inspect, document, and functionally verify each unit before shipment. It is not used, repaired, or refurbished stock unless clearly stated on the product page.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626