Sale!

Sanyo Denki P30B04010DXS8FM BL SUPER P3 100W Servo Motor

  • Model: P30B04010DXS8FM
  • Brand: Sanyo Denki
  • Series: BL SUPER P3 (square-cylinder AC servo)
  • Core Function: 100 W AC servo motor for precision motion axes
  • Product Type: AC servo motor (no brake)
  • Key Specs: 100 W rated output, 200 V AC, max 4,500 r/min, 2,000 P/R incremental encoder
  • Flange / Shaft: 30 mm (04) flange, 8 mm shaft
  • Cross-Reference: Applied Materials 0195-07983
  • ⚠️ Obsolete Model — Limited Stock Available (BL SUPER P3 superseded by later Sanyo Denki servo generations)
  • Condition: Refurbished (tested) or New Surplus — confirmed per unit
Categories: , , , , SKU: P30B04010DXS8FM Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer Sanyo Denki
Model Number P30B04010DXS8FM
Series BL SUPER P3 (square-cylinder type)
Motor Type AC servomotor (brushless)
Rated Output 100 W (0.1 kW)
Supply Voltage 200 V AC (input current approx. 1.1 A)
Rated Speed 3,000 r/min
Maximum Speed 4,500 r/min (at 200 V AC)
Brake No brake
Encoder Wiring-saving incremental, 2,000 P/R
Flange Size 30 mm (flange angle code 04)
Shaft Diameter 8 mm
Options Code 8F (connector type); CE and UL certified
Weight Approx. 690 g (with connector/jack)
Typical Application Semiconductor wafer handling, XY stages, Applied Materials tools
Common Gearhead Sanyo 017PLX0220-XX planetary gearhead

 

Product Introduction

The Sanyo Denki P30B04010DXS8FM is a 100 W AC servo motor from the BL SUPER P3 series — the square-cylinder workhorse that drives stage, gantry, and handling axes across semiconductor manufacturing equipment, especially Applied Materials platforms where it carries cross-reference 0195-07983. It runs on 200 V AC, turns 3,000 r/min rated with a 4,500 r/min ceiling, and reports position through a wiring-saving 2,000 P/R incremental encoder that cuts cable count on multi-axis machines.

Why it’s still in demand: the BL SUPER P3 generation is discontinued, but thousands of motors are running in fabs worldwide, and the 100 W / 30 mm flange frame is the most common size in that fleet. This is a no-brake variant — if your axis needs a holding brake, this is not your part. Pair it with the matching gearhead and amplifier configuration; if you’re replacing a motor on an AMAT tool, send us the full part string from the nameplate and the tool model, and we’ll confirm the exact variant before you order.

P30B04010DXS8FM

P30B04010DXS8FM

P30B04010DXS8FM

P30B04010DXS8FM

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Drive trips on overcurrent at power-up Motor winding short or phase-to-ground fault ✅ High Measure winding resistance phase-to-phase (should be balanced, typically a few ohms); then insulation resistance at 500 V Megger, >10 MΩ to frame Motor needs service or replacement
Erratic position / encoder alarm Encoder fault or damaged encoder cable ✅ High Wiggle-test the encoder connector while monitoring; check for crushed or oil-soaked cable; swap the encoder cable first Replace cable before condemning the motor
Motor runs rough, low torque Phase wiring mismatch or incorrect phase sequence ❌ Low Verify phase wiring against amplifier manual — U/V/W swapped motors vibrate and lose torque Correct wiring; motor is fine
Motor hot with normal load Bearing wear, contaminated bearing, or overloading from gearhead problems ✅ High Check for grinding noise, axial/radial shaft play; measure current draw against nameplate 1.1 A Bearing service or motor replacement
Motor won’t rotate, no alarm Amplifier fault or mechanical jam in the driven axis ❌ Low Rotate the shaft by hand with power off — if it binds, the gearhead or mechanism is the problem Fix the mechanics; don’t replace the motor
Oil / coolant inside connector area Seal failure on the tool or the motor shaft seal ✅ High Inspect the connector and rear encoder cover for liquid contamination Address the leak source; the motor may need a full teardown

Field reality: on BL SUPER motors in fab tools, encoder cables and liquid contamination cause more failures than the windings themselves. Before ordering a motor, isolate whether the fault follows the motor or stays with the cable/amplifier — swap cables if you can. If you’re still stuck, contact technical support with the drive alarm code, winding resistance measurements, and photos of the nameplate — we’ll help you confirm the motor is the actual failure.

 

Frequently Asked Questions

Q1: Can I swap this motor without losing my axis alignment?
The motor itself, yes — position feedback comes from the 2,000 P/R incremental encoder, so after a swap you re-home the axis per your tool’s procedure and you’re back. The critical part is mechanical: on AMAT tools this motor usually drives through a planetary gearhead with a specific mounting orientation. Mark the gearhead position and coupling relationship before you unbolt anything, and take photos of every connector and keyway. Seriously — I’ve never regretted photos on a semiconductor tool teardown, and I’ve always regretted skipping them.

Q2: Do I need the gearhead too?
Depends what failed. If the motor is electrically dead but the gearhead turns smoothly by hand with no grinding or excessive backlash, reuse the gearhead. If you’re hearing bearing noise or the gearhead is contaminated, replace both — a failing gearhead will kill a new motor in weeks. We stock this motor both bare and as the motor + 017PLX0220-XX gearhead assembly (AMAT 0195-07983). Tell us which configuration you need, and we’ll quote both if you’re unsure.

Q3: What condition is this unit in?
The BL SUPER P3 line is discontinued, so stock is Refurbished (tested) or New Surplus when available. Every unit runs our bench sequence: visual inspection for shaft damage and corrosion, winding resistance check phase-to-phase with a calibrated meter, 500 V Megger insulation test (>10 MΩ to frame), bearing condition check by hand-rotation and axial play measurement, encoder verification on a matching driver (pulse count and signal integrity across the full 2,000 P/R), a supervised test run at rated speed under load, and a thermal soak. We document results per unit. Test reports and photos are available before purchase — just ask.

Q4: Why is this cheaper than the OEM channel?
Applied Materials and Sanyo Denki’s distribution charge allocation pricing on discontinued fab components. We source from decommissioned tools and surplus stock, refurbish in-house, and sell with full test documentation. The motor is genuine Sanyo Denki — the supply route is the difference. For a fab running a 20-year-old tool with a known replacement roadmap, this is the economically correct option.

Q5: What warranty do you offer?
A 1-year replacement warranty on functional failure under normal operating conditions. Not covered: liquid/chemical ingress (a real risk in wafer processing tools — check your shielding), physical damage from crash events (axis crashes crack encoder boards), and damage from running with a faulty amplifier. If the unit fails in warranty, we replace it from stock — no repair-queue waiting.

Q6: Can I use a newer Sanyo Denki motor as a substitute?
To be honest, this is a hassle and usually not worth it. The BL SUPER P3 pairs with its own amplifier generation and the wiring-saving incremental encoder scheme; newer SANMOTION motors use different encoder protocols and connectors. A “modern replacement” means swapping the amplifier, recabling, and re-validating the axis on a qualified tool — in a fab, that’s a qualification project, not a swap. Matching the exact part number keeps your tool validated. If you’re planning a platform upgrade, tell us and we’ll talk options, but for a repair, buy the matching part.

Q7: How fast can you ship, and do you ship internationally?
Worldwide via DHL, FedEx, or UPS, typically within 1–2 business days for in-stock units. Because this is a discontinued part common on AMAT tools, stock moves fast — semiconductor spares buyers tend to buy the moment they see stock. Units ship in ESD-protective bagging, with shaft protection, bubble-wrapped, and double-boxed with a QC Passed label and test date. For a tool-down situation, call us directly — we’ll confirm physical shelf stock before you commit.