Sale!

Vibro-Meter MPC4 200-510-076-114 VM600 Machinery Protection Card

  • Model: MPC4
  • Part Number: 200-510-076-114
  • Brand: Vibro-Meter (Meggitt)
  • Series: VM600 Machinery Protection System
  • Core Function: Multi-channel machinery protection and real-time monitoring
  • Product Type: Machinery Protection Card
  • Key Specs: 4 dynamic channels + 2 tachometer channels; programmable for acceleration, velocity, and displacement
  • Condition: New Original / New Surplus

Description

3. Key Technical Specifications

  • Dynamic signal inputs: 4 independent, fully programmable channels
  • Accepted sensor types: Acceleration, velocity, displacement (proximity probes)
  • Tachometer (speed) inputs: 2 channels (proximity, magnetic pickup, or TTL)
  • On-board processing: Relative & absolute vibration, Smax, eccentricity, thrust position, housing expansion, dynamic pressure
  • Frequency range: DC to 60 kHz (–3 dB)
  • Input voltage range: DC 0 to ±20 V; AC ±10 V max
  • Common-mode voltage range: –50 V to +50 V
  • CMRR: >60 dB at 50 Hz
  • Crosstalk: –72 dB
  • Input impedance: 200 kΩ
  • Front-panel features: Buffered BNC connectors for raw signals; status LEDs for errors, OK system, and alarms
  • Pairing requirement: Works with corresponding IOC4T input/output card
  • Versions available: Standard, separate-circuits, and safety (SIL) versions
  • Form factor: Hot-swappable VM600 rack card

4. Product Introduction

The Vibro-Meter MPC4 (part number 200-510-076-114) is the core machinery protection card in the VM600 series. It simultaneously processes up to four dynamic sensor signals and two speed channels, delivering real-time multi-parameter measurements for critical rotating equipment.

This card is widely used on steam and gas turbines, compressors, and other high-value machinery. It provides programmable protection for vibration, position, and related parameters while offering buffered front-panel access and clear status indication for reliable operation in rack-based VM600 systems.

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
No valid measurement or “Not OK” status Sensor/cable fault or wrong channel configuration ✅ High Check gap voltage / sensor power and front-panel LEDs Verify sensor wiring and channel settings; replace card if hardware fault confirmed
Processing or hardware error LED illuminated Internal fault or configuration mismatch ✅ High Record exact LED pattern and system diagnostics Reseat card; reload configuration; replace if error persists
Missing or unstable speed signal Tachometer sensor or wiring issue ✅ High Verify speed signal at BNC or terminals Check sensor type, wiring, and configuration
Alarms trigger incorrectly Incorrect setpoints, filtering, or time delay ✅ Medium Review Alert/Danger levels and hysteresis settings Adjust setpoints and filtering to match the application
No communication with rack or IOC4T Backplane contact or pairing problem ✅ High Confirm IOC4T is present and properly seated Reseat both cards; verify rack power and backplane
Abnormal signal on front-panel BNC Sensor chain or input circuit fault ✅ Medium Scope the raw signal at the BNC connector Isolate to sensor or replace the MPC4

If the issue cannot be resolved, photograph the card (labels and LEDs), note the full part number and revision, and contact technical support with system details.

MPC4 200-510-076-114

MPC4 200-510-076-114

MPC4 200-510-076-114

MPC4 200-510-076-114

6. Frequently Asked Questions (FAQ)

Q: What does the MPC4 200-510-076-114 do?
A: It is the main machinery protection card in the VM600 system. It monitors up to four dynamic signals and two speed inputs for real-time protection of rotating machinery.

Q: Which sensors are supported?
A: Dynamic channels accept accelerometers, velocity sensors, and proximity (eddy-current) probes. Tachometer channels support proximity, magnetic pickup, or TTL signals.

Q: Does the MPC4 work by itself?
A: No. It must be paired with a corresponding IOC4T input/output card in a VM600 rack.

Q: Is the card hot-swappable?
A: Yes. The MPC4 is designed for hot-swap replacement in a powered VM600 rack (follow proper safety procedures).

Q: Are there different versions of this card?
A: Yes. Standard, separate-circuits, and safety (SIL) versions exist. Confirm the exact version required for your system, especially for functional safety applications.

Q: Can it measure both vibration and axial position?
A: Yes. The programmable channels support relative/absolute vibration, thrust position, eccentricity, Smax, and related parameters.

Q: What condition and warranty do you offer?
A: We supply New Original / New Surplus stock. Units are inspected for basic functionality. Standard coverage is a 1-year warranty against defects. Always provide the complete part number 200-510-076-114 (plus any revision or SIL marking) when ordering or requesting support.