Sale!

Whittet-Higgins NSH-12 Shoelok Bearing Locknut

  • Model: NSH-12
  • Brand: Whittet-Higgins
  • Series: NSH Shoelok (inch thread)
  • Core Function: Self-locking bearing retaining nut for shaft positioning
  • Product Type: Mechanical locknut / bearing retainer
  • Key Specs: 2.360-18 thread, 82,900 lbf axial capacity, hardened alloy
  • Condition: New Original / New Surplus
Categories: , , , , SKU: NSH-12 Brand:

Description

3. Key Technical Specifications

Parameter Value
Thread 2.360-18
Nominal Thread Diameter 2.36 in (59.94 mm)
Outside Diameter 3.16 in (80.26 mm)
Face Diameter 2.84 in (72.14 mm)
Width 0.66 in (16.76 mm)
Clamp Screw 1/4-20
Suggested Tightening Torque 80 in-lb
Theoretical Axial Holding Capacity 82,900 lbf
Material Carbon steel (alloy fasteners)
Standard ANSI/ABMA 8.2-1999
Max Operating Temperature 300 °F
Weight (approx.) 0.62 lb (281 g)
Country of Origin USA
Locking Method Tangential socket-cap screws driving hardened shoes

4. Product Introduction

The Whittet-Higgins NSH-12 is a mechanical self-locking bearing retaining nut from the Shoelok series. It threads onto a shaft or spindle to position, preload, and secure bearings and other power-transmission components without a traditional lockwasher or keyway.

Hardened alloy shoes are driven radially inward by side-access socket-cap screws, producing uniform 360-degree clamping force on the shaft threads. This design allows infinite adjustment and preloading while resisting vibration and shock. The NSH-12 meets and exceeds ANSI/ABMA 8.2-1999 and is manufactured in the USA.

NSH-12

NSH-12

NSH-12

NSH-12

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Nut will not hold preload Insufficient clamp-screw torque ✅ High Verify all 1/4-20 screws torqued to 80 in-lb Re-torque in a star pattern; do not overtighten
Shaft threads damaged Improper installation or over-torque ✅ High Inspect shaft threads for scoring or deformation Replace nut; never force onto damaged threads
Nut loosens under vibration Missing or loose clamp screws ✅ High Confirm all shoes are engaged and screws are tight Reinstall with correct torque; use thread locker if specified
Difficulty threading on shaft Debris or incorrect thread size ✅ Medium Clean shaft and nut threads; verify 2.360-18 match Do not force; check for cross-threading
Uneven face seating Dirt or burr on mating surface ✅ Medium Inspect face diameter and shaft shoulder Clean thoroughly before final torque
Axial movement after install Insufficient holding capacity for load ❌ Low Calculate actual axial load vs. 82,900 lbf rating Confirm application load is within capacity

If the nut still fails to hold after these checks, photograph the installed condition, note shaft thread condition and applied torque, and contact technical support with the serial or lot marking.

6. Frequently Asked Questions (FAQ)

Q: Does the NSH-12 require a lockwasher?
No. The Shoelok design uses internal hardened shoes driven by side screws to create a self-locking clamp. A traditional lockwasher is not needed and should not be used.

Q: Can I adjust preload after the nut is installed?
Yes. Because the locking screws are accessed from the side, you can loosen, adjust axial position, and re-torque without removing the nut from the shaft.

Q: What is the maximum operating temperature?
300 °F. Exceeding this temperature can reduce the hardness of the alloy components and compromise holding capacity.

Q: Is the NSH-12 reusable?
Yes, provided the threads and shoes are undamaged and the clamp screws are in good condition. Inspect for wear or deformation before reuse.

Q: Will this nut damage the shaft threads?
When installed correctly with the specified torque, the shoes clamp uniformly without cutting or deforming the shaft threads. Over-torque or dirty threads can cause damage.

Q: Is this the same as a standard AN or N series locknut?
No. The NSH series is a proprietary tangential-locking design. It is dimensionally different and is not interchangeable with conventional locknuts that rely on a lockwasher.

Q: Why is surplus pricing available?
These are new original or new-surplus units that have never been installed. They are inspected for thread condition and screw integrity and carry a standard warranty. OEM lead times for precision locknuts can vary; ready stock reduces downtime.