Description
Key Technical Specifications
The exact model’s suffix matters. Listings for related MHD115C-058-PG1 variants describe 70.0 Nm standstill torque, 70.0 Nm holding brake torque, absolute feedback, and side-A connector orientation, but the retrieved technical listing was for the AN variant, not BA. Confirm the exact BA configuration on the nameplate and in Bosch Rexroth documentation before purchase.
- Manufacturer: Bosch Rexroth Indramat.
- Model: MHD115C-058-PG1-BA.
- Product family: MHD permanent-magnet synchronous servo motor.
- Frame / length: 115 / C.
- Winding code: 058.
- Continuous torque at standstill: 70.0 Nm, listed for the MHD115C-058 family and related PG1 configuration.
- Holding brake: PG1 variant listings specify a brake; a related PG1 variant lists 70.0 Nm brake torque. Verify the BA motor’s label and brake data.
- Feedback: Digital servo feedback with absolute position detection; the related PG1 listing specifies more than 4,096 revolutions. Verify the exact BA encoder interface.
- Mounting dimensions: 192 mm flange and 180 mm centering diameter for the MHD115C-058 family.
- Cooling: Confirm for the exact BA unit; related PG1 data identifies liquid cooling.
- Connector orientation: BA suffix indicates a configuration that must be verified from the exact motor nameplate and drawings; do not assume the side-A orientation reported for the AN variant also applies to BA.
- Maximum speed, current, weight, and IP rating: Confirm from the applicable BA documentation; do not infer these from another suffix.
- Condition, test results, and warranty: Seller-specific; obtain written details for the exact serial-numbered unit.
Product Introduction
Bosch Rexroth Indramat MHD115C-058-PG1-BA is an MHD-series permanent-magnet synchronous servo motor. The MHD115C-058 family is listed with 70.0 Nm continuous torque at standstill and a 192 mm mounting flange with a 180 mm centering diameter.
Check the complete suffix before ordering: available technical details for related PG1 motors do not establish every BA-specific feature, including connector orientation and cooling. Match the winding, feedback, brake, cooling, shaft, and connector layout to the installed motor and drive.
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to This Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Motor does not run | Drive inhibit, power circuit issue, safety interlock, or motor fault | Possible | Read the drive fault history; verify motor power wiring against the machine diagram with power isolated | Check drive enable, interlocks, and supply before replacing the motor |
| Drive reports encoder or feedback fault | Feedback cable, connector, drive setup, or encoder fault | High | Inspect feedback cable and connectors; compare the configured feedback type with documentation for the exact motor suffix | Confirm drive compatibility and feedback wiring before installing a replacement |
| Axis loses position reference | Feedback setup, cable issue, or commissioning mismatch | Possible | Review drive feedback diagnostics and follow the machine’s approved reference procedure | Do not assume position retention after a motor swap; confirm the encoder configuration |
| Holding brake does not release | Brake supply, wiring, drive output, or brake fault | High if brake is fitted | Measure brake supply at the specified terminals during the release command, using the applicable wiring diagram | Do not apply an assumed voltage; verify brake data and circuit before testing |
| Motor overheats | Overload, incorrect drive setup, or cooling problem | Possible | Check drive load and motor-temperature diagnostics; verify cooling method and required conditions for the BA variant | Confirm the exact cooling configuration; do not assume related suffix data applies |
| Replacement will not fit or commission | Wrong suffix, connector orientation, feedback, or winding | High | Compare full nameplates, mounting dimensions, connectors, and drive motor data | Stop installation if any suffix or connection detail differs |
Support note: If the fault remains unresolved, contact technical support with a full nameplate photo, drive model and fault history, motor connector photos, and the wiring diagram. Bosch Rexroth’s documentation portal supports searches by product name or material number.

MHD115C-058-PG1-BA

MHD115C-058-PG1-BA
Frequently Asked Questions (FAQ)
What is the -PG1-BA?
It is a Bosch Rexroth Indramat MHD-series permanent-magnet synchronous servo motor. The MHD115C-058 family is listed at 70.0 Nm continuous torque at standstill.
Does this exact BA version have a holding brake?
PG1 listings for related MHD115C-058 configurations show a holding brake, including a related variant rated at 70.0 Nm. Verify the BA motor’s nameplate and order documentation before relying on that rating.
Is this motor liquid-cooled?
A related PG1 variant is listed as liquid-cooled, but the available source is for the AN suffix, not BA. Confirm the cooling arrangement from the exact BA nameplate and Bosch Rexroth documentation.
Can I substitute an AN or another MHD115C-058 variant?
Not without checking. Different suffixes can identify different connector, feedback, shaft, or other configuration details. Match the complete code and wiring before ordering.
Will the absolute encoder retain position after replacement?
The related PG1 variant is listed with absolute position detection over more than 4,096 revolutions, but the exact BA feedback configuration and machine behavior must be confirmed. Follow the drive and machine commissioning procedure after replacement.
What condition is the motor in, and what warranty applies?
Condition and warranty depend on the seller and specific unit. Ask for the serial number, inspection or test report, warranty period, return terms, and written confirmation of the exact BA configuration.
What should I verify before ordering?
Send the seller the full nameplate and connector photos. Confirm the complete BA suffix, winding 058, feedback interface, brake rating, cooling method, flange and centering dimensions, and condition against the installed motor and drive.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626