Description
Key Technical Specifications
| Parameter | Value |
| Bus Architecture | PC/104 Standard (8/16-bit ISA bus compliant) |
| Protocol Support | Profibus DP, DP-V1, and DP-V2 Master / Scanner |
| Data Transfer Rate | Up to 12 Mbps (auto-baud detection) |
| Physical Medium | RS485 twisted-pair cable via DB9 or onboard header |
| Maximum Slaves | Up to 126 slave nodes per master channel |
| Operating Power Supply | +5 VDC (sourced directly from PC/104 stack bus) |
| Operating Temperature | 0 to +60 °C |
| Operating Systems | Windows NT / 2000 / XP, DOS, and embedded real-time OS drivers |
| Enclosure Format | Open-board PC/104 stackable module |
| Weight | ~0.15 kg |
Product Introduction & Supply Chain Strategy
The Brad Communications PC104-DPIO DRL-DPM-BKF is a high-performance Profibus DP master communication card designed for PC/104 embedded industrial computers. It coordinates deterministic data exchange between host control software and field-level Profibus DP slave devices, managing high-speed cyclic and acyclic communications across automated manufacturing systems.
Securing this communication card as a certified New Surplus part represents a critical supply-chain safeguard against unexpected network obsolescence failure. Because legacy PC/104 industrial computer stacks rely on exact hardware compatibility, sourcing genuine OEM stock avoids the hidden reliability hazards of refurbished or repaired interface boards. Hoarding verified factory-new surplus units guarantees system lifecycle continuity, protecting Total Cost of Ownership (TCO) without risking plant communication reliability on degraded second-hand components.

PC104-DPIO DRL-DPM-BKF

PC104-DPIO DRL-DPM-BKF
Installation & Configuration Guide
1.Pre-Installation (Prep & Safety):Prerequisite.
Isolate all power feeds to the industrial PC/104 embedded stack and apply formal lock-out/tag-out (LOTO) protocols. Ground yourself using an ESD-safe wrist strap. Verify that bus stacking power is completely discharged before handling expansion modules.
Verification: Confirm zero voltage across the PC/104 stack power rails using a calibrated digital multimeter.
2.Removal:Mechanical Extraction.
Disconnect the Profibus DB9 communication cable and any internal auxiliary wiring harnesses from the legacy card. Carefully unstack the module from the PC/104 bus headers, pulling straight upward to avoid bending pin connectors.
Verification: Inspect mating PC/104 connector pins across adjacent stack boards to ensure absolute cleanliness and zero bending damage.
3.Installation (Clone & Seat):Hardware Setup.
Configure any onboard address jumpers or termination switches on the new Brad Communications PC104-DPIO DRL-DPM-BKF card to match your legacy system parameters. Align the module pins precisely with the PC/104 stack headers and press down firmly until fully seated.
Verification: Perform a visual inspection around the perimeter of the stacked board to verify flush, uniform pin engagement across all four bus corners.
4.Power-On & Testing:Commissioning.
Restore power to the embedded PC/104 system. Load the appropriate Direct-Link driver stack and verify that the master interface initializes without throwing hardware interrupt (IRQ) conflicts or memory address overlaps.
Verification: Check that the onboard diagnostic LEDs indicate active bus power and normal token-passing traffic on the Profibus DP network.
Firmware/Software Versions & Upgrade Notes
- Driver Baseline: Ensure your operating system environment utilizes the compatible Direct-Link driver version specified for your application stack (supporting legacy Windows NT/2000/XP or targeted real-time OS environments).
- Compatibility Warnings: Do not attempt to flash legacy communication controllers with unverified firmware images, as mismatched microcode versions will break master-slave synchronization on the Profibus network.
- Configuration Retention: Back up network configuration files and GSD device database profiles from the host system before executing hardware replacement tasks.
Frequently Asked Questions (FAQ)
- Why is this Brad Communications card classified as New Surplus rather than standard factory direct?
This unit is an authentic, original OEM-manufactured product procured from verified surplus channels after industrial inventory rationalizations. It has never been installed in an active computer stack or subjected to field electrical wear.
- How can I be certain this interface card is not refurbished or repaired?
We enforce a strict zero-tolerance policy against second-hand, repaired, or rebuilt electronics. Every card arrives in original anti-static packaging featuring unblemished gold-plated bus pins, pristine solder joints, and zero component replacement history.
- What are the hidden risks of installing a refurbished PC/104 communication board?
Refurbished industrial cards frequently feature heat-stressed communication transceivers and aged passive components. These hidden defects lead to intermittent bus timeouts, packet drops, and catastrophic network freezes during critical production runs.
- Is the PC104-DPIO DRL-DPM-BKF affected by manufacturer obsolescence?
Yes, legacy PC/104 hardware platforms have experienced strict lifecycle transitions, making certified New Surplus inventory essential for maintaining aging embedded systems without costly redesigns.
- What warranty terms apply to this New Surplus communication card?
This product is backed by a comprehensive 1-year replacement warranty, matching standard OEM reliability benchmarks and protecting your capital investment.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626