Sale!

EPRO PR6423/000-101-CN Emerson 8 mm Eddy Current Sensor

The EPRO PR6423/000-101-CN is an 8 mm non-contact eddy current sensor from Emerson’s EPRO machinery monitoring range. It is designed for critical turbomachinery — steam, gas and hydro turbines, compressors, gearboxes, pumps and fans — where it measures radial and axial shaft dynamic displacement, shaft position, eccentricity and speed/keyphasor signals without touching the shaft.

Categories: , , , , SKU: PR6423/000-101-CN Brand:

Description

Core Product Summary

The EPRO PR6423/000-101-CN is an 8 mm non-contact eddy current sensor from Emerson’s EPRO machinery monitoring range. It is designed for critical turbomachinery — steam, gas and hydro turbines, compressors, gearboxes, pumps and fans — where it measures radial and axial shaft dynamic displacement, shaft position, eccentricity and speed/keyphasor signals without touching the shaft.

Configured per its order code, this variant has an M10x1 case thread without armored cable, a 25 mm sleeve, no adapter plug, and an approximately 4 m integral cable with an open cable end. The sensor delivers a 2 mm linear measurement range with an 8 V/mm incremental scale factor (±5% over 0 to 45 °C) and reaches an IP66 protection rating, with an operating range of -35 °C to +180 °C for the sensor including its first metre of cable. To produce a usable signal, the probe must be connected to a matching EPRO signal converter such as the CON021, which then feeds EPRO MMS monitoring systems.

 

Key Technical Specifications

Parameter Value
Product type 8 mm eddy current sensor (non-contact displacement probe)
Order code configuration M10x1 case thread, no armor, 25 mm sleeve, without adapter plug, approx. 4 m cable, open cable end
Linear measurement range 2 mm (80 mils)
Initial air gap 0.5 mm (20 mils)
Incremental scale factor (ISO) 8 V/mm (203.2 mV/mil) ± 5% at 0 to 45 °C
Deviation from best fit straight line (DSL) ± 0.025 mm (± 1 mil) at 0 to 45 °C
Minimum shaft diameter 25 mm (0.79 in)
Target material (standard) 42CrMo4 (AISI/SAE 4140) ferromagnetic steel
Operating temperature — sensor incl. 1 m cable ‘-35 °C to +180 °C
Operating temperature — cable and connector ‘-35 °C to +150 °C
Protection class IP66 per IEC 60529
Case thread M10x1
Standard cable diameter 2.8 mm, minimum bending radius 25 mm
Case material / tip Stainless steel case, PEEK sensor tip
Approvals CE, ATEX, IECEx, CSA; intrinsic safety (ia) and non-sparking (nA) protection

 

Detailed Product Overview

The PR6423/000-101-CN belongs to Emerson’s EPRO eddy current transducer family, the sensing element of a modular measurement chain used in machinery protection and condition monitoring systems. The probe works on the eddy current principle: its coil, energized by an external signal converter, generates a high-frequency electromagnetic field, and the distance between the probe tip and the conductive shaft surface modifies the energy absorbed by eddy currents in the target. The converter translates this into a DC bias voltage proportional to the average gap, with the dynamic AC component superimposed — one signal therefore carries both shaft position and shaft vibration information.

For an engineer specifying a replacement probe, three characteristics of this order code matter most. First, the mechanical configuration: an M10x1 threaded stainless steel case with a 25 mm sleeve allows installation in standard EPRO holders and locknuts, while the open cable end means the field cable must be terminated directly rather than via a Lemo connector — a detail that affects both the extension cable plan and the converter connection on site. Second, the electrical characteristics: the 2 mm linear range with an 8 V/mm scale factor matches the standard configuration used across the PR6423 family, so the probe fits existing converter scaling where the same 8 mm system is already installed. Third, the calibration dependency: the specified scale factor and linearity apply to the matched sensor–cable–converter system, and the stated accuracy figures are defined over 0 to 45 °C, so gap settings and alarm thresholds derived from these values should be checked against the actual ambient conditions at the bearing.

The sensing performance is bound to the target material. The 8 V/mm scale factor and ±0.025 mm linearity figures apply to shafts made of 42CrMo4 (AISI/SAE 4140) steel or a material with comparable electrical and magnetic properties; other shaft materials change the effective sensitivity and require recalibration of the measuring chain. The minimum shaft diameter of 25 mm also constrains installation, and runout measured on smaller targets will not meet the stated linearity.

Environmentally, the IP66 rating allows the probe to operate permanently in dust and wash-down conditions at the machine, and the sensor tip tolerates surface temperatures up to 180 °C, while the cable and any connector interface are limited to 150 °C — a boundary that matters when routing the cable near hot casing areas. The hazardous-area approvals (ATEX, IECEx, CSA) with intrinsic safety (ia) and non-sparking (nA) modes of protection support installation in classified areas, with temperature classes T6, T4 or T3 depending on the ambient temperature.

Typical uses are radial shaft vibration and axial thrust measurement on turbine trains, eccentricity and keyphasor measurement, and static position measurement where a non-contact method is required. The dynamic measuring chain, completed by the converter, supports frequency components up to 20 kHz, which covers the vibration signatures of high-speed rotating machinery.

PR6423/000-101-CN

PR6423/000-101-CN

PR6423/000-101-CN

PR6423/000-101-CN

Dimensions, Mounting & Connection Notes

  • Case thread: M10x1, with a 25 mm sleeve length for this order code; standard M10 hardware uses SW 8 mm wrench flats on the case and SW 17 mm on the locknut side.
  • The probe installs non-contact, facing the shaft surface, with the initial air gap set at 0.5 mm (20 mils) inside the 2 mm linear range during commissioning.
  • Standard (unarmored) cable diameter is 2.8 mm with a minimum bending radius of 25 mm; route the cable away from surfaces above 150 °C.
  • Sensor including its first metre of cable is rated -35 °C to +180 °C; the cable and connector section is rated -35 °C to +150 °C.
  • Protection class IP66 (IEC 60529) for the installed sensor.
  • The cable end is open (unterminated) on this variant and must be connected to the signal converter or extension wiring accordingly.

 

System Compatibility & Integration Requirements

Item / Dependency Verified Compatibility or Requirement Practical Note
Signal converter Operates with matching EPRO eddy current signal converters (e.g., CON021 family) The probe is passive; scale factor and linearity apply to the complete sensor–cable–converter chain
Converter supply (CON021 type) ‘-23 V to -32 V (output -4 V to -20 V) or -21 V to -32 V (output -2 V to -18 V) Supplied from the monitoring system, not the probe
Measuring chain frequency response 0 to 20,000 Hz (-3 dB) via the converter Relevant for high-speed machinery diagnostics
Monitoring system Signal processed by EPRO MMS series monitoring modules Converter output feeds the monitor input channel
Mounting thread M10x1 case thread, 25 mm sleeve Use matching EPRO holders/locknuts; wrench flats per M10 hardware
Cable termination Open cable end on approx. 4 m integral cable Field termination required; cable bend radius min. 25 mm
Measured target 42CrMo4 (AISI/SAE 4140) steel, min. shaft diameter 25 mm Other materials require recalibration of the chain

 

FAQ

What is the EPRO PR6423/000-101-CN?
It is an 8 mm non-contact eddy current sensor from the Emerson EPRO product family, configured with an M10x1 case thread, no armor, a 25 mm sleeve, no adapter plug, and an approximately 4 m integral cable with an open cable end.

What does it measure?
It measures radial and axial shaft dynamic displacement, shaft position, eccentricity and speed/keyphasor signals on rotating machinery such as steam, gas and hydro turbines, compressors, gearboxes, pumps and fans.

What are its key specifications?
Linear measurement range 2 mm, initial air gap 0.5 mm, incremental scale factor 8 V/mm ± 5% over 0 to 45 °C, deviation from best fit straight line ± 0.025 mm, and IP66 protection per IEC 60529.

Does the probe work standalone?
No. The sensor is one part of a measuring chain and requires a matching EPRO signal converter (such as a CON021 type) to energize the probe and produce a scaled output for the monitoring system.

Which shaft material is it calibrated for?
The stated scale factor and linearity apply to 42CrMo4 (AISI/SAE 4140) steel or a material with comparable properties; different shaft materials require recalibration, and the minimum shaft diameter is 25 mm.

What temperature limits apply?
The sensor including 1 m of cable operates from -35 °C to +180 °C, while the cable and connector section is limited to -35 °C to +150 °C.

Which approvals does it carry?
The sensor family carries CE, ATEX, IECEx and CSA approvals, with intrinsic safety (ia) and non-sparking (nA) modes of protection for hazardous-area installation; temperature class depends on ambient temperature.

What should be checked when replacing an existing probe?
Verify that the replacement matches the original order code’s cable length, termination type and thread, because the scale factor and linearity figures apply to the complete matched sensor–cable–converter chain.