Description
Key Technical Specifications
| Parameter | Specification / Value |
| Model Number | LASC-100W8 |
| Manufacturer | Yaskawa Electric Corporation |
| Board Type | High-Speed Differential Line Driver & Signal Conditioning Board |
| Signal Compatibility | RS-422 Differential Line Driver / Open-Collector Inputs |
| Logic Power Input | +24 V DC (±10%) / +5 V DC Regulated Output |
| Channel Density | Multi-channel differential pulse/direction and encoder feed-through |
| Max Frequency Response | Up to 4 MHz differential pulse transmission |
| Isolation Voltage | 1500 V RMS optocoupler/galvanic signal isolation |
| Operating Temperature | 0 °C to +55 °C (32 °F to 131 °F) |
| Mounting Type | Direct card-cage insertion or Servopack slot option |
| Unit Weight | 0.45 kg (0.99 lbs) |
Product Introduction & Supply Chain Strategy
The YASKAWA LASC-100W8 is a specialized high-speed line driver and signal conditioning board engineered for Yaskawa direct-drive motor systems and advanced Servopack control architectures. It converts command pulses and high-resolution encoder position feedback into noise-immune RS-422 differential signals, allowing reliable long-distance signal transmission between motion controllers and heavy-duty direct-drive motors without signal degradation or electrical interference.
Because Yaskawa has transitioned active manufacturing toward newer motor control platforms, acquiring genuine New Surplus LASC-100W8 boards is essential for maintaining operational production lines. Replacing a failed line driver with a second-hand or refurbished board poses severe operational risks, including degraded optocouplers, dry solder joints, and signal jitter that can cause motor hunting, position drift, or overcurrent trips. Keeping 1–2 New Surplus units as strategic buffer stock provides immediate swap capabilities and ensures uncompromised motion precision.

LASC-100W8

LASC-100W8
Installation & Configuration Guide
Electrical Shock & Position Deviation Hazard
Servo drives and direct-drive motors store high DC voltage in internal capacitors. Disconnect main power feeds and wait at least 5 minutes before handling interface boards. Always wear a grounded ESD wrist strap to prevent static destruction of sensitive CMOS line driver ICs.
1.Pre-Installation & ESD Setup:5 mins.
Lock out/tag out (LOTO) power to the motion controller and drive cabinet. Attach a grounded ESD wrist strap connected to earth ground. Document existing jumper pin settings, cable routing, and terminal wiring on the legacy board.
2.Removal of Outgoing Board:5 mins.
Unscrew front faceplate retaining screws or release mounting clips. Disconnect interface ribbon cables and terminal blocks carefully without pulling directly on individual wiring leads. Slide the board straight forward out of its card slot.
3.Hardware Configuration & Board Seating:5 mins.
Match DIP switch positions and jumper pin settings on the new LASC-100W8 to mirror the original unit exactly. Slide the board smoothly into the card cage guide tracks until edge connectors engage fully, and tighten retaining screws.
4.Wiring Reconnection & Power-On Test:10 mins.
Reconnect signal and power cable harnesses securely. Restore logic power, check diagnostic LEDs for normal operation, and perform a slow manual jog test to verify clean pulse transmission and position tracking.
Verification: The drive controller display must show normal communication status without differential encoder error alarms (e.g., A.C90 encoder communication error or line driver signal loss faults).
Firmware/Software Versions & Upgrade Notes
- System Compatibility: Designed for Yaskawa legacy direct-drive motor controllers and multi-axis motion cabinets requiring RS-422 differential line driving.
- Plug-and-Play Hardware: The LASC-100W8 functions as a hardware-level signal driver board and does not hold flash firmware. Swapping the board requires no software download or drive flashing.
- Jumper Verification Precaution: Verify all terminal selection jumpers (line driver vs. open collector input modes) prior to powering the system, as incorrect jumpering can cause input signal clipping or pulse loss during high-speed motion execution.
Frequently Asked Questions (FAQ)
Is this YASKAWA LASC-100W8 board brand new or refurbished?
This product is Brand New Surplus. It is not a pulled board, second-hand card, or refurbished item. It features factory-original line driver ICs, pristine PCB trace contacts, and uncompromised signal isolation components.
Why shouldn’t our facility buy cheaper refurbished or used line driver boards?
Refurbished line driver boards often contain fatigued optocouplers and aging capacitors that suffer from increased propagation delays and pulse distortion. In direct-drive motor systems, minor pulse distortion leads to positioning errors, motor vibration, and unexpected high-speed tracking faults.
What are the main signs that an existing LASC-100W8 board is failing?
Common indicators include intermittent position feedback errors, pulse count mismatches, erratic motor movement during acceleration, and red fault LEDs on the drive controller indicating loss of differential signal integrity.
Do I need to calibrate or program the board after installation?
No programming is required. The board operates at the hardware signal interface layer. Simply ensure all hardware configuration jumpers match the outgoing board’s settings prior to powering up.
What warranty is provided with this New Surplus board?
Every New Surplus YASKAWA LASC-100W8 board is backed by a standard 12-Month Replacement Warranty. Units undergo comprehensive quality verification checks—including visual inspection, trace continuity, and power-on logic testing—before ESD-safe packaging and dispatch.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626